Rice Transplanter
1. Maintenance before operation
(1) Clean the machine. Clean the body, remove mud and debris, entanglement; clean the air filter, radiator, oil-water separator. Clean up the residual fertilizer in the fertilizer tank, as well as the fertilizer trough wheel and discharge brush, etc.; remove the dirt and sundries at the trench opener and the fertilizer outlet. (Applicable to side deep fertilization device)
(2) Check and add fuel, coolant (water) and engine oil. Check the fuel and coolant (water) margin, if insufficient should be timely filling. Clean or replace the fuel filter element according to the maintenance cycle specified in the manual; check, supplement or replace the engine, gearbox, rear axle box, planting box and other parts of the oil. When replacing the oil, the oil filter element should be replaced at the same time.
(3) Add lubricating grease. According to the requirements of the instructions, apply or add lithium-based lubricating grease to the planting arm, rotating box, moving bracket, pontoon, connecting rod, drive shaft, sliding block, guide rail, clutch and other parts.
(4) Inspection of operation parts and engine transmission parts. Check the wear, deformation, lubrication and clearance of seedling feeding mechanism, crank, swing rod, seedling claw, planting fork, etc. If it does not meet the use requirements, replace or adjust it; Check whether the fertilizer box, fertilizer grooved wheel, fertilizer bellows and air bellows are damaged or air leaks, if any, please repair or replace them in time (applicable to side deep fertilization device); Check the front and rear tires for wear; check, adjust or replace engine belt, gearbox drive belt and longitudinal conveyor belt; check and adjust each handle, pull rod and pull wire; check or replace seedling pusher and seedling needle.
(5) Start-up check. Check whether the starter motor, generator, horn, lights and other electrical components are normal, whether the engine has abnormal noise, whether the exhaust smoke color is normal, whether the instrument indication is normal, etc., and repair the fault in time.
(6) Operation Department inspection. Check whether the seedling loading platform, seedling feeding parts, planting arm and other planting parts work normally, and repair them in time if any fault is found; Check whether the fertilizer drainage grooved wheel and blower are running normally, such as fertilizer drainage jam and other timely maintenance (applicable to side deep fertilization device).
(7) Walking inspection. Start slowly, check whether the transplanter runs smoothly, whether the brake and transmission work normally, etc., and repair the fault in time.
(8) Try planting inspection. According to agronomic requirements, adjust the planting distance, seedling quantity and planting depth, carry out trial planting, and check the quality of planting operation until it meets the index requirements. If the seedling leakage rate does not meet the index requirements, the number of horizontal transmissions should be reduced to increase the sampling amount. If the seedling drift rate does not meet the index requirements, the planting depth should be appropriately increased.
(9) Fertilization amount inspection (applicable to side deep fertilization device). Adjust the height and angle of the furrow opener according to the agronomic requirements of side deep fertilization, set the target fertilization amount, weigh the fertilization amount after running for a certain distance, count the actual fertilization amount according to the operation area, and adjust the opening of the fertilizer dispenser until the actual fertilization amount meets the operation requirements.
2. Maintenance in operation
(1) During operation, the machine should be started gently to ensure that there is no leakage and continuous fertilizer in the initial stage.
(2) During transplanting, seedlings should be installed in time when the seedlings in the seedling box are planted to a short length. Do not hold the seedlings with your hands to prevent your hands from hurting your hands when picking up the seedlings.
(3) When the rice transplanter sags, please do not pull or lift it up forcibly. The paddy wheel can be used to plug sticks. Sticks with a length of 650mm and a diameter of 100mm can be inserted into the paddy wheel blades. The paddy wheel rotates to make the machines and tools gradually leave the sinkage zone.
(4) when the transplanter turns, the seedling box and fertilizer box should be lifted to stop planting and fertilization. Avoid reversing, reversing is likely to cause blockage of the fertilization port.
(5) During the working process of the transplanter, ensure that the pontoon is clean and avoid the accumulation of debris on it to the drive shaft or universal joint.
(6) After the operation is completed, the fertilizer box should be cleaned in time, and the fertilization parts should be cleaned and refueled regularly to prevent the fertilizer from adhering to rust (applicable to the side deep fertilization device).
3. Safety operation tips
(1) Carefully read and fully understand the instructions and the warning signs and prompt signs pasted on the product.
(2) Please do not operate the machine after drinking, lack of sleep and overwork.
(3) In the process of transplanting, the machine operator and the seedling feeder should perform their respective duties and cooperate with each other to avoid operation accidents of the seedling feeder. If adjustment is required, the transplanter must be shut down and relevant adjustments must be made after flameout.
(4) Do not drag heavy objects with transplanter.
(5) When entering and leaving the field and crossing the ridge, drive at a low speed and strictly follow the operation method in the instruction manual.
(6) When parking, be sure to place the main shift lever in the neutral position, step on the brake pedal, and turn off the engine if necessary.
Source: Maanshan Agricultural and Rural Bureau
Website: https://mp.weixin.qq.com/s/6r0m5JYSDKD00f9g1sHUTw
