corn precision seeder
corn precision seeder
Maintenance before (I) operation
1. opener installation adjustment. The seeding furrow opener must be used with the fertilizing furrowleft and rightdirection is staggered by more than 50mm to avoid chemical fertilizer burning seedlings.
2. Sowing row spacing adjustment. Adjust the row spacing of the planter according to the local agronomic requirements; During adjustment, the center line of the beam frame of the planter is used as the baseline, and the single sowing unit and the ditching parts for fertilization are moved symmetrically to the left and right. At the same time, the support wheel, transmission mechanism andRow fertilizer boxalso need to adjust accordingly. The moved parts should be re-tightened.
3. Adjustment of sowing spacing. Adjust accordingly according to the broadcasting gauge in the instruction manual, hook up the corresponding sprocket and tighten it.
4. Fertilization depth adjustment. Loosen the top wire on the fixed seat of the fertilizing furrow opener and move the plow up and downColumn Adjustmentdepth, up is shallow, down is deep. It is required that the lower tip of each fertilizing furrow opener is parallel to the rack, and it is recommended that the fertilizing furrow opener is better than the seedingopener depth 50mm, in order to achieve deep application of chemical fertilizers.
5. Fertilization amount adjustment. Crop varieties, number of seedlings per mu (ridge spacing andplant spacing), soil fertility determines the amount of fertilizer applied per mu, according to the requirements of the amount of fertilizer applied, to support wheel rotation 10 times shall prevail, determinationfertilizer drainersthe size of the excluded fertilizer, and then calculate it.mu of discharged fertilizer(slip rate is calculated at 10%) until adjustmentFertilizer discharging device reaches to muquantity shall prevail.
6. Sowing depth adjustment. adjust the on each seeding monomerdepth limit pointerhandle, when operating, let each seeding monomerDepth limit indicator needle is inthe same scale position to ensure the same sowing depth of the whole machine. BroadcastDeep Adjustment, the actual sowing depth should be measured. When the indicated sowing depth is inconsistent with the actual sowing depth, secondary fine-tuning should be carried out to achieve sowing.deep consistency.
7. Adjustment of seeding rate. Hitopen seedcover adjusts the partition, the partition positioning hole moves up, the replay rate decreases, but the cavity rate increases; the partition positioning hole moves down, the cavity rate decreases, but the replay rate increases. Need to repeatedly adjust the test, to achieve a satisfactory state.
(II) operation
1. Observationin seed pipethe seed position, when the upper plane of the seed is close to the bottom of the tube, it should be added in time, otherwise it is easy to miss sowing.
2. The speed of the tractor should not be too fast, otherwise it will affect the quality of sowing.
3. haveSpecial person to follow the machine to monitor:Seed platter and fertilizer platterturn normally, frontwith or without orange stubble blockage, broadcastis deep or not, with or"Drying Seeds"phenomenon, problems must be eliminated; troubleshooting before continuing operations to ensure that the sowing state is in good condition.
4. When the planter arrives at the ground, check the amount of seed in the seed box and the amount of fertilizer in the fertilizer box, and add it in time when it is insufficient.
5. Maintenance shall be performed before each shift or land change operation, and regular shutdown for maintenance shall be performed during operation.
(III) safety operation tips
1. When the planter starts the operation, the planter should be dropped while walking. The planter should not be put into the soil violently to avoid severe impact damage to the buried working parts and avoidcause seed guiding nozzleand fertilize the opener port blocked.
2. It is strictly forbidden to adjust, repair and lubricate during sowing operations. Working parts and transmission parts clayor excessive entanglement of grass, must stop cleaning.
3. Don't be aroundscribeget off the station and walk back and forth in front of the crew to avoid personal accidents.
4. The planter is not allowed to make sharp turns and reverse during operation to avoid damage to the seeding parts.
5. When sowing mixed seeds, the staff should wear goggles, masks and gloves and other protective equipment. The remaining seeds after sowing shall be properly treated and shall not be eaten to prevent human and animal poisoning.
Source:Sangma dialect Liangzhou
Website: https://mp.weixin.qq.com/s/9sL-A8wJsiq-Yb28ynqkag
