fixed (mobile) type grain dryer overhaul technical guide
fixed (mobile) type grain dryer overhaul technical guide
1. Maintenance before operation
(1) Look for power. The power supply voltage shall be stable and within ± 5% of the rated voltage, and a secondary leakage protection device shall be provided; check whether the power line is damaged; and whether the power supply is truly grounded.
When the mobile grain dryer is installed or used for the first time after replacing the power system, please reconfirm the grounding effect.
(2) Check whether the grain loading and discharging mechanism and the internal drying circulation mechanism are blocked, and clean up if they are blocked. At the same time, it is necessary to clean up the residues inside the machine and the residues inside the dust collection chamber.
(3) Overhaul the transmission parts. Check whether the belt and chain are damaged, and replace them if they are damaged; check the tightness of the belt, and press the middle part of the belt for 10~15mm with your fingers, if it is not satisfied, adjust it; check the tightness of the transmission chain, press the middle part of the chain for 5~10mm with your fingers, if it is not satisfied, adjust the left and right screws of the lower section of the elevator; check whether the ladle (bucket) is damaged, if there is damage or wear, it should be replaced; check whether the blade of the auger is bent, cracked or the edge is worn (wear thickness> 20% needs to be replaced). Check whether the motor, fan, hoist and other transmission parts are running normally. If there is any abnormality, repair or replace it in time. Check the lubrication of each motor, bearing and chain. If it is insufficient, add lubricating oil (grease) in time.
(4) Check the exhaust duct and dust exhaust duct. Check whether there is any foreign matter inside, and clean it if necessary; whether it is deformed or damaged, and replace it if necessary.
(5) Check the moisture meter. Clean the roller and brush of the moisture meter and calibrate the moisture meter. If the accuracy deviation of the moisture meter is large, it should be replaced.
(6) Check the control system. Check whether the temperature sensor, alarm device and other components are normal and effective. If there is any abnormality, repair or replace them in time. Check whether the controller, voltmeter, ammeter, indicator light and other electrical components on the control cabinet work normally. If there is any abnormality, repair or replace them in time.
(7) There should be no obstacles or flammable materials around the machine, and the working path should be kept more than 1.5 meters away from the machine.
(8) Check safety protection devices. Check whether the protective cover of each rotating part, the protective device of hot air pipe, flue and other heating parts, and the protective net cover at the air inlet of heat exchanger and fan are firmly installed and effectively protected. If there is any abnormality, replace or repair it in time.
(9) The mobile grain dryer should check whether the load-bearing column of the equipment is reliably supported, and the tires should be 10-20mm from the ground. Check the level that comes with the device to determine whether the device is still tilted and adjust it in time. Check the granary lifting locking rod, lifting the auger to ensure reliable locking.
2. Maintenance in operation
(1) When it is found that there is seepage or leakage of grain (oil, gas) at the connection of each part of the dryer, the machine should be shut down for maintenance, and the seals should be replaced or repaired in time.
(2) If there is still no temperature drop after the high temperature alarm, the heat source should be cut off immediately and the machine should be shut down for maintenance to prevent fire in the warehouse.
(3) Observe whether the flame is stable (burner type) and check whether there is any abnormal smell. If there is any abnormality, stop the machine immediately to find out the cause and eliminate the fault.
(4) Pay attention to whether there is abnormal sound of each motor and transmission parts, whether there is metal friction sound in the operation of the auger (blade scraping wall), whether the belt speed of the transmission belt is normal, whether the bucket falls off or deforms, whether the belt/chain slips and jumps, etc. If any abnormality is found, stop the machine for maintenance immediately.
(5) When unloading grain, if there is a sudden decrease in grain discharge flow, observe whether the grain discharge tee is blocked. If blocked, stop the machine in time to prevent the hoist from stopping and causing damage.
(6) often check whether the fasteners are loose, check whether the bolt is loose or fall off, such as loose or fall off should be timely fastening or reset.
(7) Routine maintenance of the hoist every 60 days of use. Check whether the motor coupling of the hoist is worn and whether the fixing bolts are loose; check whether the bucket is worn and the tightness of the bucket belt; check whether the bucket belt is deviated or the edge is worn, and replace or tighten it in time if any.
(8) Routine maintenance of the grain spreader every 60 days of use. Check whether the keyway connecting the shaft of the grain spreader and the motor is worn and whether the fixing bolts are loose. If so, replace or tighten them in time.
(9) Clean and lubricate regularly. Regularly check the bearings, sprockets, chains and other transmission parts, according to the operating state in a timely manner to clean and add lubricating oil (grease).
3. Safety operation tips
(1) Check whether it is equipped with a dry powder fire extinguisher. The fire extinguisher should be within the validity period.
(2) do not stay too long after the grain into the machine, should be immediately air or dry. The amount of grain loaded shall not be greater than the maximum rated capacity of the dryer and shall not be overloaded.
(3) When the dryer is running, it is strictly forbidden for the operator to touch the operating mechanism of each part of the dryer with his hands; when the dryer is abnormal, it should be shut down for maintenance immediately, and it is not allowed to operate forcibly. After the drying operation is stopped, do not cut off the main power supply immediately. Please ventilate and run for more than 5 minutes first, and let the machine continue to supply air to cool the combustion chamber before stopping the machine. Otherwise, the unburned gas in the combustion chamber may produce abnormal sound and spray out hot gas, which will cause burns.
(4) When the mobile grain dryer is in operation, the operator shall not touch the hot air blower or the parts near the burner or pull out the hot air blower to prevent burns or scalds. It is strictly prohibited to use articles other than the sample extractor or fingers into the sample sampling port to prevent mechanical failure or injury caused by articles or personnel involved.
(5) When the operators are overhauling, they should work with more than two people, need to be supervised, wear safety helmets, and fasten safety belts when climbing high.
(6) In addition to spot inspection or maintenance, the control box door should be in a closed state to prevent dust and foreign matter from entering the control box, causing internal failure, short circuit or fire.
(7) It is forbidden to replenish fuel during the operation of the dryer; when replenishing fuel, fireworks are strictly prohibited.
Source: Maanshan Agricultural and Rural Bureau
Website: https://mp.weixin.qq.com/s/6r0m5JYSDKD00f9g1sHUTw
