agricultural machinery repair
B90
HuapeoplepeopleTotalandcountrycountryhome.standardquasi
GB/T22129-2008
General technical specification for agricultural machinery repair
Repairingall-purposetechnicalcriterionagriculturalmachinery
2008-06-26Release
2009-01-01realapplication
the People's Republic of China General Administration of Quality Supervision, Inspection and Quarantine countrycountryhome.standardquasipipeCommitteewill |
haircloth
GB/T22129-2008
Words
This standard is proposed by the Ministry of Agriculture of the People's Republic of China.
This standard is under the jurisdiction of the National Agricultural Machinery Standardization Technical Committee.
Drafting unit of this standard: Agricultural Machinery Maintenance Research Institute, Ministry of Agriculture.
Main draftsmen of this standard: He Chen, Yang Jinsheng, Yu Zhigang, Zhang Jianlong, Sun Liying,Liu Xuebin.
GB/T22129-2008
General technical specification for agricultural machinery repair
1
This standard specifies the technical requirements for major agricultural machinery repair operations.
This standard applies to the repair of agricultural machinery.
2Normative references
to become provisions of this standard through reference in this standard. Any Wang datethe reference file, all of its subsequentamendment orders (excluding errata) or revisions do not applythis standard, however, the parties to an agreement under this standard are encouraged to studywhether the latest versions of these files are available. For undated references, the latest version is applicable to this standard.
GB3847-2005vehicles and compression ignition engine automobile exhaust smoke emission limit and measurement methodGB/T3798.2-2005Vehicle OverhaulNo.-Part 2: Truck
GB/T3799.2-2005Commercial Vehicle Engine OverhaulPart 2: Diesel enginesGB/T5770-2008Diesel engine plunger type fuel injection pump assemblyTechnical Conditions
GB7258-2004Technical conditions for safe operation of motor vehicles
GB10395.1-2001Tractors and machinery for agriculture and forestrysafetyPart 1: General (eqv.ISO4254-1:1989)
GB10396-2006Agricultural and forestry tractors and machinery, lawn and garden power machinerysafety signs and hazard graphics(ISO11684:1995,MOD)
GB/T15746.1-1995vehicle repair quality inspection and evaluation standardVehicle overhaul
GB/T15746,2-1995vehicle repair quality inspection and evaluation standardengineoverhaul
GB16151.1-2008agricultural machinery-Part 1: Tractors
GB/T16739.1-2004Conditions for the opening of the auto repair industryPart 1: Vehicle maintenance enterprises
GB/T16784.2-1998Industrial products after-sales servicePart 2: Maintenance
3Fault Judgment and Removal
3.1Before dismantling agricultural machinery (tools), first remove the external soil and grease,is washed with high-pressure water, the electrical equipment shall be removed (to be protectedprotection) to avoid moisture, performance appraisal before disassembly, assembly technical performance should not be disassembled, disassembled parts should be identified according to the specified procedures,custody.
3.2Special tools shall be used when disassembling. Disassembled parts, components and assembliesneatly placed.
3.3pay attention to the removal direction and sequence.
3.4disassembly.
3.5When removing the rolling bearing from the shaft diameter, the stressed part should be on the inner ring of the bearing.. When removing the rolling bearing from the bearing chamber, the stressed part shall beon the bearing outer ring.
4Maintenance operation conditions
4.1Facility conditions
4.1.1Maintenance enterprises: the structure and facilities of the production plant shall meet the requirements of agricultural machinery overhaul and assembly repair operations, water and electricity, heating (heating requiredgroundarea) and other reliable supply, and in line with the relevant provisions of production safety, environmental protection, health or fire protection.
4.1.2Maintenance network: the production plant area should be adapted to its production program and production process. Corresponding production safety measures shall be provided.
4.1.3On-site maintenance: The agricultural machinery after field maintenance should meet the use requirements. Protection against repair modes of excessive machine wear, Bao
GB/T22129-2008
witness safety.
4.1.4Repair, processing, assembly, running-in, test and inspection of main assemblies and parts shall be carried out in the production plant.
4.2Personnel Conditions
4.2.1enterprise managers should have the ability of enterprise operation and management, andunderstand the regulations and standards of agricultural machinery maintenance and related industries, in lineGB/T16739.1-20044.2. Technical director should be familiaraware of the regulations and standards of the agricultural machinery maintenance business and related industries.GB/T16739.1-20044.3.
4.2.2The setting of technical types of work should be appropriate to the scope of production in which they are engaged, and the number of technical personnel for each type of work should be appropriate to their production program and production process.
adaptation.
4.2.3Technical personnel of various types of work shall receive professional training.
4.3Equipment Conditions
4.3.1The type, specification and quantity of equipment equipped by the repair and maintenance enterprise shall be compatible with its production program and production process, in line withGB/T16739.1-20049.1,9.2. The technical condition of the equipment is in good condition, which shall meet the requirements of processing, testing accuracy and use requirements, and conform to the requirements of the equipment.GB/T16739.1-20049.4.
4.3.2shall have special equipment for maintenance operations, testing, testing and diagnostic equipment, general equipment, measuring instruments and main hand tools, in accordance with the requirements ofGB/T16739.1-20049.1.
4.4maintenance safety production conditions
4.4.1Maintenance enterprises should have safety management appropriate to the content of their maintenance operations.management system and safety protection measures to establish responsibility for safe productionsystem. Safety protection measures, fire-fighting facilities should comply with the relevant industry regulations, in lineGB/T16739.1-20046.1provisions.
4.4.2There shall be safety protection measures and facilities for toxic, flammable and explosive materials, dust and corrosive agents, pollutants, pressure vessels, etc., in line with the requirementsGB/T16739.1-20046.3.
4.5Organization Management Conditions
4.5.1operation and management conditions meetGB/T16739.1-20045.1.
4.5.2Should have agricultural machinery maintenance quality commitment, into the factory registration, inspection, completion of the factory certificate management, technical files.management, standards and metrologymanagement, equipment management and maintenance, personnel technical training and other systems, in line withGB/T16739.1-20045.2.3.
4.5.3shall establish agricultural machinery maintenance files and import and factory registration ledgers.Agricultural machinery maintenance files should include maintenance contracts, incoming, process, completion inspection.records, factory certificate sub-page, settlement vouchers and working hours, material clearancesheets, etc., conformGB/T16739.1-20045.2.4.
5Repair
5.1Technical requirements for engine repair
5.1.1The contact surface between the cylinder head and the cylinder block meets the design requirements.
5.1.2The inclined surface of the head plate of the valve seat and the working inclined surface of the valve seat meet the design requirements. Valve sag exceeds allowable, the valve seat insert should be used.ring method to restore the original design requirements.
5.1.3When the seat hole of the main bearing bush does not meet the design requirements, the main shaft should be repaired by surface repair technology.tile hole.
5.1.4The cylinder liner shall meet the design requirements. When the inner diameter of the cylinder liner exceeds the secondary repair size, the cylinder liner shall bescrapped.
5.1.5Pistons meet the design requirements, and the quality of the same group of pistons is not much differentin 7g ~ 15g.
5.1.6When the connecting rod meets the design requirements and the parallelism exceeds the allowable value, the connecting rod shall be corrected.is on the right.
5.1.7When the crankshaft meets the design requirements and the shaft diameter exceeds the fourth-class repair size, surface repair shall be adopted.technology, repair according to the original design requirements
the crankshaft.
5.1.8The flywheel shall meet the design requirements, and static balance test shall be carried out after repair..
5.1.9the camshaft meets the design requirements.
5.2enginecombination and test
5.2.1The engine shall be assembled according to the assembly process requirements. and conformGB 3799.2-20054.2.3.
5.2.2timing gear according to the mark.
GB/T22129-2008
5.2.3If cold running-in and hot test are required for the assembled engine, the running-in, hot test and cleaning shall be carried out according to the process requirements. and conformGB 3799.2-20054.2.10.
5.2.4engine cylinder compression pressure in accordanceGB/T15746.2-1995B1.4.1. The pressure of each cylinder is in accordance with the average pressure difference of each cylinder.GB/T 15746.2-1995B1.4.2.
5.2.5The idling operation of the engine under normal working conditions shall comply with the provisions of B1.3.2 in GB/T15746.1-1995. Engine running performance meetsGB/T 15746.1-1995B1.3.3.
5.2.6The starting performance of the engine shall comply with the provisions of B1.2.1 and B1.2.2 in GB/T 15746.2-1995.
5.2.7The maximum idling speed and idling speed range of the engine shall be adjusted according to the original engine regulations, and the maximum power shall not be less than 95% of the original design calibration value. The maximum torque shall not be less than 95% of the original design calibration value. The fuel consumption rate is not higher than 2% of the calibration value.
5.2.8The engine oil pressure shall meet the requirements of B1.11 in GB/T 15746.2-1995.
5.2.9The engine exhaust device shall be complete and effective. The emission limits shall comply with the provisions 6.3 in GB 3847-2005.
5.2.10The fuel injection pump shall be assembled according to the technical conditions approved by the original manufacturer. The inspection method shall comply with GB/T 5770-2008.
5.2.11The limit deviation of the interval angle between the oil supply starting point of each cylinder of the multi-cylinder oil pump and the specified reference cylinder is ± 0.5 ° cam angle.
5.3motor repair
5.3.1When the rotor shaft diameter and bearing chamber do not meet the design requirements, surface repair technology should be used to repair and process according to the original design requirements.
5.3.2After the winding coil is replaced, the wire diameter and number of turns shall be consistent with the original winding resistance.
5.3.3fixedsub and the outer surface of the rotor are slightly worn, turning can be carried out according to the original design requirements (within the allowable range)..
5.4motor after repair
5.4.1The motor shall be assembled according to the procedures specified by the original manufacturer. The outgoing line mark shall be correct, the rotor shall rotate flexibly, and the radial deflection of shaft extension shall meet the design requirements.
5.4.2After the motor is repaired, it must pass the winding inter-turn withstand voltage test, the winding to the casing and their mutual withstand voltage test, short circuit test, heating test and overspeed test.
5.4.3winding to the casing and its mutual, determination of the DC resistance of the winding in the cold state, determination of the transformation ratio (wound-type motor) and determination of the no-load resistance.
5.5transmission parts
5.5.1The gear meshing position and meshing clearance during gear transmission shall meet the design requirements, and the locking mechanism shall be effective.
5.5.2The pulley (sprocket) meets the design requirements. Belt (chain) drive tensioning device is effective.
5.5.3The performance of the main components of hydraulic transmission and pneumatic transmission machinery and equipment shall meet the design requirements.
5.6working parts
5.6.1The rotary working part shall rotate according to the same motion track, and its circular runout and axial swing difference shall meet the design requirements.
5.6.2reciprocating working parts shall be on the same level. After assembly, the assembly shall be able to move back and forth flexibly without beating or abnormal noise driven by the driving mechanism. The installation position of the components at the limit position shall meet the design requirements.
5.6.3The fixed working parts shall be installed firmly, and the local clearance of the contact surface shall meet the design standards. Its shape, position and installation dimension shall meet the design requirements.
5.6.4The working parts shall have sharp cutting edge, smooth movement, no deformation and no welding, and the cutting edge hardness shall meet the design requirements.
5.6.5Seeder working parts
5.6.5.1The amount of seed and fertilizer discharged after the maintenance of the precision seeder meets the design requirements. Row spacing, plant spacing (hole spacing), sowing uniformity, ditching depth and soil covering thickness meet the requirements of agricultural technology.
5.6.5.2The seed meter has complete parts and flexible rotation of the seed meter shaft.
5.6.5.3Mechanical single-grain (precision sowing) seeder seeder seed breakage rate ≤ 1.5, large displacement range, reliable adjustment and no slippage.
5.6.6rice transplanter working parts
5.6.6.1drainage valve is flexible to adjust, open and close the same, and the coefficient of variation of the stability of the total fertilizer discharge is less than or equal to 7.8.
5.6.6.2The seedling claw and seedling feeder shall meet the design requirements, and no welding repair is allowed.
5.6.6.3Working time of working parts such as seedling claw, seedling feeder and box shiftercooperate correctly.
GB/T22129-2008
5.6.6.4pointsThe transplanting mechanism and seedling feeding mechanism meet the design requirements. The number of seedlings (adjustable) meets the requirements of agricultural technology. Cave distance and insertion depth can be adjusted.
5.6.7The furrow tip (furrow opener) of the multi-row seeder and the working machine shall have the same furrow depth, the seedling claw row, seedling feeding fork, cutter, etc. shall be on the same straight line, and the longitudinal center line of the monomer shall be perpendicular to the frame.
5.7Shaft and box
5.7.1The drive shaft shall meet the design requirements after repair, and the maximum outer diameter linear velocity shall be greater5 m/s is less than 25 m/s, the static balance test shall be carried out, and when it is more than 25 m/s, the dynamic balance test shall be carried out.
5.7.2shaft diameter shall meet the design requirements after repair, and the coaxiality shall meet the design requirements.
5.7.3spline shaft meets the design requirements after repair, and the coaxiality meets the design requirements.
5.7.4After the shaft is repaired, it meets the design requirements, and the radius of gyration meets the design requirements. Heat treatment after crank welding repair.
5.7.5The box (body) meets the design requirements. After the bearing chamber is repaired, it shall be processed according to the original design requirements and painted according to the color of the original machine.
5.8conveying device
5.8.1screw conveyor blade shall be free of cracks, open welding and deformation. The adjustment clearance shall meet the design requirements. The method of checking the static balance of the screw conveyor should be able to stop it at any speed.
5.8.2The inclined conveyor chain is not deformed, broken, and the climbing teeth are free of defects, the height is consistent, and the adjustment gap meets the design requirements.
5.8.3The belt conveyor shall be free of deflection and damage, the rivets and buckles shall be firm, and the joints shall be tightly covered.
5.9steering system
5.9.1The front wheel alignment inspection shall be carried out after the steering system is assembled, and its parameters shall meet the design requirements.
5.9.2steering wheel is easy and flexible to operate without bias or jamming. Do not interfere with other components during steering.GB7258-2004. The amount of free rotation of the steering wheel is in accordanceGB 7258-2004.
5.9.3The hydraulic steering system complies with the provisions of 8.7 and 8.8 in GB 16151.1-2008.
5.10brake system
5.10.1The service braking performance shall comply with the provisions 7.2 in GB 7258-2004.
5.10.2The emergency braking system shall comply with the provisions 7.3 in GB 7258-2004.
5.10.3The parking brake performance shall comply with the provisions 7.4 in GB 7258-2004.
5.10.4The braking performance of a motor vehicle with pneumatic braking is in accordance with the provisions 7.7 in the GB7258-2004. Air brake equipment compliesGB7258-2004.
5.10.5The hydraulic brake device shall comply with the provisions 7.5 in GB 7258-2004.
5.11Hydraulic system
5.11.1The components of the hydraulic system (hydraulic pump, control valve, cylinder, hydraulic motor), connecting pipelines and accessories are complete, with good performance and reliable operation.
5.11.2The technical requirements for running-in test of hydraulic oil pump (hydraulic motor) shall conform to the original design regulations. The flow test shall be carried out with a hydraulic system detector (hydraulic test bench) under the conditions of rated pressure, calibrated rotation speed and oil temperature of 50 ℃ ± 5 ℃, and the volumetric efficiency shall not be lower than the original design requirements (gear pump 85%, plunger pump 95%). Distributor (valve), oil cylinder, motor and other running-in test requirements shall meet the original design requirements; the technical indicators shall be tested by hydraulic system detector (hydraulic test bench); the indicators shall meet the design requirements.
5.11.3hydraulic system in accordance with GB 16151.1-200811.3.
5.11.4The hydraulic suspension and traction device shall comply with the provisions of 11.1 and 11.4 in the GB16151.1-2008.
5.11.5split hydraulic system complies with the provisions 11.2 in the GB16151.1-2008.
5.12electrical equipment
5.12.1Main performances such as ignition performance, magnetic stability performance and ignition conversion advance angle of the magneto meet the design requirements.
5.12.2permanent magnet alternator shall be free of open circuit, short circuit and grounding, and its insulation performance and rotor magnetic flux shall meet the original design requirements.
5.12.3The excitation coil of the DC generator is well insulated, and the insulation performance of the armature coil, the insulation performance between commutator segments and between commutator and armature meet the original design requirements.
GB/T22129-2008
5.12.4The insulation performance of the stator coil of the silicon rectifier generator, the resistance value of the excitation coil, the collector ring, the diode and the brush shall comply with the original regulations.
5.12.5generator is matched with the regulator, connected in parallel with the battery, and the negative pole is ironed. The technical requirements of the assembled AC and DC generators shall comply with the original manufacturer's regulations.
5.12.6The excitation coil, armature, commutator, carbon brush, one-way clutch and electromagnetic switch of the starter meet the original manufacturer's regulations.
5.12.7The battery shell shall be free of cracks, with good wiring, firm installation, sufficient power and technical performance in accordance with the original factory regulations.
5.12.8lighting signal devices and other electrical equipment comply with GB 7258-20048.
5.13Rack and Walk
5.13.1The rack (frame) shall be complete with complete accessories, free of cracks and deformation, and the welding parts shall not be unwelded. The rivets shall not be loose, and the places connected by bolts shall be tightened and locked reliably.
5.13.2The various tie rods and guide rods between the frame and the suspension shall not be deformed, and the joints and bushings shall not be loose or displaced. The leaf spring shall be free of cracks and fragments. The form and specification of the spring shall meet the design requirements. The central bolt andUbolts shall be tightened.
5.13.3The hub, rim, web and lock ring shall be free of cracks and deformation, and the nuts shall be complete and reliable.
5.13.4The number of left and right track shoes of crawler tractor (half-track equipment) and relevant requirements shall meet.GB 16151.1-2008.
5.13.5The tire model of wheeled tractor (equipment) shall meet the requirements of the original vehicle, and the technical requirements shall meet the requirements.GB16151.1-2008.
5.13.6The tread direction of the driving wheel should not be reversed (except in the desert). The left and right tires on the same axle have the same model and tread, and the wear degree is roughly the same. CompliantGB 16151.1-2008.
5.14assembly and adjustment
5.14.1All parts shall be identified and cleaned before assembly. The assembled parts, components, assemblies and accessories shall meet the corresponding technical conditions and be fully equipped. It is allowed to change some parts, components and design according to the technical documents approved by the prescribed procedures during the repair process, but the design shall not be lower than the original design requirements.
5.14.2parts and moving parts, they are not allowed to be exchanged with each other, and the assembly marks shall be carefully checked.
5.14.3for some assembly technology requirements are higher, can not change the direction of the parts to identify the assembly direction.
5.14.4After the assembly of mechanical equipment, the clearance of each part shall be adjusted, and the size of the clearance shall meet the design requirements of the original machine. The adjustment of the operating machinery shall meet the agronomic requirements.
5.14.5The lifting (lifting), lowering speed and height of the machine; the adjustment of the up and down, left and right positions of the working parts should comply with the original machine regulations.
5.14.6The hydraulic system of variable displacement pump is adopted, and the oil supply amount shall be adjusted according to the original machine under the condition of ensuring the oil supply pressure.
5.14.7distributor, the automatic tripping pressure and the pressure of the oil cylinder overload safety valve shall be adjusted according to the regulations of the original machine.
5.15running-in
5.15.1The no-load running-in specification and load running-in specification of each type of locomotive (mechanical equipment) shall be in accordance with the original running-in specification.
5.15.2should observe the operation of the engine, check the water temperature, oil temperature and the reading of the oil pressure gauge; check the clutch, gearbox, driving wheel, final transmission, steering mechanism and hydraulic system, and all parts of the vehicle (machine) Whether the technical status is intact; after the running-in test, the adjustment of the clearance of each part should conform to the original machine.
5.16whole machine and appearance
5.16.1For power machinery (operation machinery) and other assemblies (parts), the signs, numbers and marks shall be complete and the handwriting shall be clear; the number plate shall be intact and shall be placed at the specified position; the safety signs shall comply with the requirements.GB10396-2006are set in a conspicuous position.
5.16.2The appearance of the whole machine is neat, the curved surface is round and smooth, and the painting quality conforms to the provisions 4.1 in GB 3798.2-2005. The mechanical parts, instruments, lead seals and auxiliary equipment are complete and effective; the clutch, brake, accelerator pedal, and joystick should be able to automatically return to position; all parts of the whole machine must not be modified to hinder operation, affect safety and limit the performance of the original machine.
5.16.3All pipe joints, valves, sealing gaskets, oil seals, water seals, screw plugs and joint surface gaskets are complete and intact, and the joints are tight; no oil, water, air and electricity.
5.16.4All moving parts that can cause injuries must be provided with protective plates, covers, sleeves or fences in the possible contact positions with human bodies, which meet the requirementsGB10395.1-2001.
GB/T22129-2008
5.16.5The parts, components, assemblies and accessories of the mechanical equipment after repair shall be complete, conform to the requirements of relevant standards and technical documents, and shall pass the inspection.
6Acceptance Steps
6.1maintenance shall be judged according to the repair quality of the corresponding agricultural machinery.
6.2When handling the handover procedures for the repair of qualified machinery and equipment, the repair unit shall, in accordance with GB/T 16784.2- 19984to the provisions of Chapter 1, the repair certificate and repair record sheet shall be delivered to the repair unit (or individual). The maintenance record sheet shall indicate the name, content, quantity and price of the repair machinery or equipment, and shall be signed by the repair unit (or individual). For the format of the maintenance record, referGB/T16784.2-1998 AppendixAor otherwise designed.
6.3The repair unit shall guarantee the quality of the completed machinery and equipment, and the quality guarantee time shall refer to the relevant provisions of the original machine when it leaves the factory. In the case of strict implementation of the regulations, reasonable use and normal maintenance by the repair unit (or individual), the repair unit shall be responsible for rework and repair of the repair quality problems during the quality assurance period.
