Spring Plowing Production Agricultural Machinery Maintenance Technical Guide (III)-Tractor Maintenance
-Tractor Maintenance
Tractors are mainly used for traction and driving various supporting machines and tools. They are power machinery for completing agricultural field operations, various earthwork operations, transportation operations and fixed operations. Doing a good job of technical maintenance can slow down the deterioration of the technical status of various parts, reduce failures, extend service life, and ensure that the tractor often works in good condition.
1, carefully clean the tractor appearance of oil and dust. Check whether the connecting bolts and nuts of main parts are loose, and tighten them in time. Check whether the diesel oil, engine oil and cooling water are sufficient. Check the oil level of the engine oil pan, and add enough when it is insufficient. Check the tire pressure. After the engine is started, let the locomotive run at idle speed for 3 to 5 minutes, let the lubricating oil fully enter the working parts, and check whether the instrument, light and horn are normal. Check whether the brake oil pipe is worn and the tightness of the pipe mouth connection, and pay special attention to whether the brake oil pipe collides with the bridge package and the frame. Check the on-board tools.
2. Check the lubrication system. In addition to replacing the three cores (air filter element, diesel filter element, oil filter element), replace or clean each hydraulic oil filter element. Lubricating oil and fuel should be replaced according to regional and seasonal requirements. If the lubricating oil has been released years ago, the oil filler on the cylinder head should be opened. After adding qualified lubricating oil, let it stand for ten minutes. Check the oil dipstick. It should be flush with the "upper" line of the oil dipstick. Then let it stand for 20~30 minutes to check whether the oil level has changed. If there is an increase, find the cause and troubleshoot. If it is an engine with a turbocharger, you need to remove the hollow bolt of the oil inlet of the turbocharger suspension bearing, drop a few drops of lubricating oil, and install it again. The grease nipple and oil cup shall be complete. All lubricating parts and assemblies shall be filled with enough lubricating oil or grease according to the specified oil. The ventilator shall be clean and unblocked.
3. Check the cooling system. In cold areas, focus on checking whether the engine has frostbite, especially for cars that did not drain water or did not add antifreeze a year ago. Carefully check the engine's body water blockage, water drain switch, oil radiator, etc. for signs of frost cracking. If it is normal, fill soft water until the water tank mouth is flush, and let it stand for one hour to see if the water level changes. If the water level drops, you need to find the cause. If there is no drop, it is normal. Pay attention not to add well water and tap water that are easy to produce scale.
4, check the circuit system. The circuits of starting, lighting and instrument shall be normal, and the insulation parts of all electrical accessories shall be free of leakage and short circuit. The cold start device of the engine in cold area should be able to work normally. Check the battery observation hole: green means that the battery is fully charged; black means that the battery is not fully charged; white means that the battery is basically uncharged. When the observation hole of the battery shows black, it is necessary to recharge the battery. When the observation hole shows white, it is necessary to replace the battery. When the battery is low, it should be charged with one tenth of the rated current of the battery. When charging the lead-acid battery, the electrolyte level is flush with the engraved line or 10~15mm higher than the separator. Open the filling plug to prevent the outlet from being blocked and the battery explodes due to high air pressure. After charging is completed, the single battery voltage should be around 13 volts.
5. Check and change the oil quantity of engine oil pan. Pull out the oil dipstick located on the left front of the engine oil pan and check whether the oil level is between the upper and lower engraved lines. If the oil level does not reach the lower engraved line, remove the fuel filler cap on the engine timing gear chamber cover for refueling. During maintenance and oil change, the oil drain plug at the lower part of the oil pan should be unscrewed, dirty oil should be drained and cleaned, and then new oil should be added.
6. Inspection and maintenance of hydraulic steering oil tank. The hydraulic steering oil tank is set at the upper end of the engine. Open the fuel tank cap (with dipstick) to observe whether there are oil marks on the dipstick. If there are no oil marks, it means that the amount of oil in the steering oil tank is insufficient. Check to find out the cause of the oil leakage, and then remove the oil tank. Add the oil to the middle of the dipstick and put it back in place. During the inspection, the system shall check that the hydraulic steering cylinder, oil pipe and joints shall not leak oil, otherwise it is easy to cause steering failure, and the filter screen in the oil tank shall be cleaned or replaced regularly. When checking the oil level, check whether the vent valve (such as rivet-like) in the center of the oil tank cap is flexible. If there is oil pollution, it should be cleaned.
7. Check and change the oil quantity of engine oil pan. Pull out the oil dipstick located on the left front of the engine oil pan and check whether the oil level is between the upper and lower engraved lines. If the oil level does not reach the lower engraved line, remove the fuel filler cap on the engine timing gear chamber cover for refueling. During maintenance and oil change, the oil drain plug at the lower part of the oil pan should be unscrewed, dirty oil should be drained and cleaned, and then new oil should be added.
8. Check the steering system. Pay attention to the clearance between the left and right directions, and observe the clearance between the rod ball end drive and the cylinder (hydraulic cylinder direction) pin shaft. If the clearance is too large, replace the rod ball end and the cylinder pin shaft. After replacing the ball head and pin shaft, check the toe. The toe of the four-wheel drive is 0~4mm, and the toe of the two-wheel drive is 5~10mm.
9. Check the clutch. Check the gap between the clutch pedal and the release bearing and the release lever to ensure thorough and flexible separation without jamming. When the pedal stroke is 4/5, the shift position can be hung without abnormal noise. If the clutch has been used for too long, it is necessary to disassemble and check the friction plate and release bearing. If it exceeds the limit, it needs to be replaced; if the wear is not large, add grease to the release bearing and then assemble it according to the standard.
10. Check the brake. Check the brake fluid level and pedal stroke. The first foot of the brake pedal can be pressed to death at one time, and the second foot cannot be pressed continuously. The return is normal and there is no seizure. The heights of the left and right brake pedals should be synchronized.
After the above are checked to be normal, the main and auxiliary transmission handles should be in the "empty", "down", "middle" or "separated" position before starting; the hydraulic power unit should be in the "middle" position; at this time, you can open the flywheel housing In the small window, use a small crowbar to toggle the flywheel ring gear, turn the crankshaft several times, and then turn on the ignition switch to start the power. The speed needs to be low first and then high, gradually increase the power speed, and at the same time observe the instrument and listen carefully to the sound. If there is any abnormality, stop the machine first and then check and troubleshoot.
