Created on:2024-09-01

(full version) summary of agricultural machinery knowledge points

plough

1. are divided into traction plow, suspension plow and semi-suspension plow according to different ways of coupling with tractor.

1. Tractionploughstructure: it is mainly composed of traction device, plough frame, plough wheel, plough body, small front plough, round plow blade, lifting mechanism and adjusting mechanism.

Features:①the longitudinal size of the plow body is not limited, so more plows can be configured..②complex structure, heavy weight.

③large turning radius.④metal consumption, high price.

2. SuspensionploughStructure: The suspension plow is much simpler than the traction plow structure. It is generally composed of a plow frame, a suspension frame, a main plow body, a plow blade, an adjusting device and a depth limiting wheel.

Features:①strong maneuverability, flexible turning.②metal consumption is small, light weight, low cost.

③on tractor driving wheel weight gain effect is good.

3. semi-suspendedploughStructure: The front end of the plough is suspended by the tractor, and the rear end is the depth limiting wheel and tail wheel mechanism. Its structure is composed of the first two parts respectively.

Features:①weight is lighter than traction plowabout1/3, but the longitudinal size of the plough is not limited.;②is better than that of traction plow.

4. Turning plow (two-way plow)

turning plough is divided into left turning, right turning and horizontal turning. Its main advantages are: leveling the surface after ploughing, reducing the empty stroke of the ground head and improving work efficiency.

2.tillage soil ratioresistanceKt: Longitudinal horizontal resistance per unit cross-sectional area of soil during ploughing under standard conditions.

The so-called standard operating conditions, refers to the use of standard plough body, in the commonly used tillage depth range, commonly used tillage speed and suitable tillage water time to measure the force, calculated.outKt.

plowing soil specific resistance comparison intuitively discriminates the difficulty of plowing soil.

3. main plough body

function: cut, break, flip the soil, in order to achieve the purpose of covering weeds and residual roots, loose soil.

composition: composed of ploughshare, plough wall, plough side plate, plough heel, plough column, etc. Some plows have extension plates in order to strengthen the turning effect of the plow..

4. plough side plate

plough is located at the rear of the plough, which bears and balances the side pressure generated by the plough body during work to ensure the stability of the plough width. The side plate of the last plow of the multi-share plow is the most stressed and worn out, and is generally equipped with a replaceable plow heel.

①plough side plate in horizontal plane

in order to make the reaction force of the ditch wall act on the rear end of the plough side plate to increase the plough width stability. The front end of the side plate should be separated from the trench wall line, that is, there is a certain horizontal gap, and its value is generally5~10mm.

②Configuration of Plough Side Plate in Vertical Plane

the distance between the front end of the plough side plate and the bottom plane of the trench is called the vertical gap.

vertical gap reduces the reaction force of the soil to the side plate of the plough, so that the depth limiting wheel of the plough bears a certain supporting reaction force, so that the plough depth remains stable; at the same time, the soil clearance angle is increased to facilitate the plough into the soil. General vertical clearance10~20mm.

5. the process of turning over the soil (drawing)

in the work, the plough plow out of the rectangular soil. where the share blade cuts out its widthdegreesB, shin blade cut out its depthdegreesa. There are three modes of movement of the soil on the surface of the plow: rolling, rolling and rolling. In the northern general-purpose plough in the form of rolling.

in the study of soil movement process, there are three assumptions:

①soil section remains unchanged during the overturning process and is always rectangular;

②The soil strip is not broken;

③turnover.

6. height adjustment unit:is working, the hydraulic system of the tractorin"floatmovement"state, the plowing depth is controlled by the depth limiting wheel.

7. lead curve: the ripe plough body is required to have better soil crushing performance, and the lead curve is set at a distance from the plough.tip2/3on the plane of the plough.the half-spiral (turning-up) plow body, it is located at the end of the share.

For the lead curve with the same opening, the closer the position is to the tip, the better the soil crushing performance, on the contrary, the better the soil turning performance.

8. produce four different traction states according to the different positions of instantaneous center, resistance center and power center:

positive traction:π2is located on the center line, and the traction line passes through the power center line.

partial traction:π2is located on the right side of the centerline, and the traction line is parallel to the forward direction of the unit, but is in line with the powerHeartCdeviation distancefrome.

Oblique traction:π2is located to the left of the center line, but the traction line passes through the power center line.

skew traction: instantaneousHeartπ2is uncertain, but the pull line is neither through the power.HeartC, it is also not parallel to the direction of advance.


9. partial traction phenomenon: any traction line does not pass through the power center and causes the deflection torque of the unit, which makes the tractor produce automatic deviation, is called partial traction phenomenon.

(1) Essence of partial traction adjustment

by adjusting the position of the lower suspension point relative to the plow frame, to changechangeπ2the position, so as to change the direction of the pull wire, in order to eliminate or reduce the deflection moment.

note: in the adjustment should keep the tillage width unchanged, should look after each other.

(2) Adjustment Method

①first shift the suspension shaft (only the left and right suspension points can be moved on the plow equipped with the plow width adjuster) to make the traction line pass through the power center, thus forming the oblique traction phenomenon.

②the adjustment may cause the ploughshare deflection, the deflection can be eliminated by changing the front and rear positions of the lower suspension point.

10. traction plough

1.ploughing depth adjustment

operation, according to the requirements of ploughing depth, timely rotate the ploughing depth adjustment wheel, shorten the length of the lead screw when the ploughing depth becomes shallow, otherwise the ploughing depth becomes deep. If the plow is controlled by hydraulic pressure, different positions of the positioning baffle on the piston rod can be changed to obtain different tillage depth, while the upward movement increases the tillage depth and the downward movement becomes shallow.

2.horizontal adjustment

operation, it is required that the frame should be parallel to the ground plane to make the ploughing depth of the left and right ploughs consistent, otherwise, the horizontal adjustment wheel should be rotated to adjust.

3.Tail Wheel Adjustment

: ensure that the depth of the last plough is the same as that of the first plough. If not, adjust the vertical adjustment screw, screw in, after the end of the shallower, on the contrary, deeper.

horizontal adjustment: mainly to adjust the side pressure of the plough side plate and tail wheel. When the horizontal adjustment screw is screwed in, the tail wheel moves in the direction of uncultivated land, and vice versa.

4.Adjustment of traction linewhole

(1) Adjustment of traction lineaccordingresistance center theory (United States, Western Europe); centroid theory (former Soviet Union, Eastern Europe)

(2) Principles and methods of adjustmentlawtraction line adjustment: the traction line must pass through the resistance center or the center of gravity of the plowtraceSpoint and keep parallel to trench wall

XI. Consequences of Improper Position of Traction Wire

In the horizontal plane:

traction line deviates to the right: the plow frame is twisted counterclockwise, the total tillage width is narrowed, heavy tillage occurs between the ploughs, and the soil is not turned well..

traction line deviates to the left: the total tillage width becomes wider, there is leakage between the plough bodies, the surface is uneven after ploughing, the soil is not broken well, and the side surface of the plough side plate is severely worn.

common point is that the plow wheel inclines, which aggravates the wear of the axle sleeve and axle and increases the resistance.

In vertical plane:

The traction line is too high: the front part is lowered, the rear part is tilted, the load of the ground and groove wheels is aggravated, the axle is worn seriously, the front plow is deep and the rear is shallow.

traction line is too low: the front part of the plow frame is raised, the grasping force of the ground wheel is reduced, the lifting fails, the wear of the tail wheel axle is aggravated, and the front shaft is shallow and the rear shaft is deep.

disc harrow

1.disc harrow: used for crushing soil after ploughing, raking before sowing, and shallow tillage after harvesting.

2.classification:

1.according to the arrangement: single row rake, double row rake; opposed type, offset type

2.by weight:light (rake straightdiameter460mm), Medium(560mm), heavy(660mm)

3.divided by hooking method:Traction type, suspension type, semi-suspension type, etc.

3.rake deflection angle: refers to the angle between the rotation plane of the rake and the forward direction of the machine under working conditions.

4.disc harrow:1.rake group:1) Rakepiece2)partyshaft3)roomtube4)shaftBearing5) Scraping plate

2.Rake

3. Angle adjuster:(1) workusedchanging the size of the angle of each rake group to change its working depth,, the larger the contact area between the concave surface of the disc and the soil, and the greater the pressure of the soil on the concave surface of the disc, thus increasing the rake depth. On the contrary, the rake depth becomes shallow.

(2) groupangle adjuster is composed of upper and lower sliding plates, tooth plates, clips, supporting plates, front pull rods, rear center pull rods, etc.

4.Weight box, weight plate

5.transport wheel

6.Main Tunewhole

depth and light tonewhole(1)the deflection angle is increased, the depth of penetration increases, otherwise it becomes shallower.

(2)the weight is added to the weight plate and the weight box, the weight will become deeper when the weight increases, otherwise it will become shallower.

Sowing Machinery

1. seed treatment methods:1.seed pointslevel2.pellets3.offvelvet4.seed coating

2. laying film seeding mechanical composition:


1.Shaperstructure

function: push away the surface dry soil, press out the compact membrane bed, and open the membrane edge small ditch at the same time.

composition: including soil dividing plate (haveVtype) and shaping rollers (cylindrical and drum-shaped).

2.Fertilization institutions

Common forms of furrow opener: hoe shovel type, sliding force type, single disc type, etc..

3.Laying Mechanism

function: complete the operations of film spreading, film laying, film pressing and soil covering.

composition: including film roller, film spreading roller, film pressing wheel, earth disc, etc. The film spreading roller is a cylindrical or drum waist-shaped shaft. There are two types of film pressing wheels: integral type and separate type.

4.seeding mechanism

function: complete the seed arrangement under the membrane or on the membraneindustry

1)broadcastUsed for seeding under the film, the main working parts are the outer grooved wheel seeder and the double disc opener.

2) pointbroadcastis used for under-film or on-film seeding, and the main working part is the sowing wheel.

5.hole covering mechanism

function: cover and suppress the seed holes that have been sown.

3. outer sheave seeder

structure:

Leak-proof:


(1) Front wall inclinationangleα1should be greater than the seed's natural angle of repose.

(2) The seed passage should be wide and narrow, so that the seeds can easily fill the seed cup, and at the same time, it is not easy to flow.

(3) Seed tongue lengthdegreesm = 22~26mm, opendegreesCk =6~8mm, big seeds can be bigin10, small seeds can be smallin6, the angle should be less than the natural repose angle of the seed to prevent the seed from flowing.

4. air suction type seed meter

Seed disc structure parameters

①straightdiameterd: usually minussmalld,inυma certain time, can be reducedlowυp, is conducive to the absorption of species, reduce the leakage of sowing, but will make the organization large, air consumption also increased, so the current domestic and foreign more.usedd=140~260mmdisc.

②Suction hole diameter and shape: The shape of the suction hole is mostly circular, and burrs should be removed. The diameter is determined according to the size of the planted crop seeds. Jadem5~6mm, largebeans4~5mm, sweet pelletsdish2~3mm.

③Number and arrangement of suction holes

there are many suction holes, the spacing between adjacent suction holes is small, which is easy to absorb redundant seeds. At the same time, there is more air leakage, which requires more air volume. It is better to have a little more without affecting the suction, scraping and dropping of seeds. The arrangement of suction holes includes single row, staggered double row, hole group, thin strip hole and inclined seam.

Plant Protection Machinery

1.application

①spray method: the pressure liquid is atomized through the nozzle, and the droplets are straightdiameter100~300μm.

②Mist method: the use of high-speed air flow will be coarse fog droplets broken, blowing, fog droplets straightdiameter75~100μm.

③Ultra-low volume spray method: the use of high-speed rotating disc generated by the centrifugal force to throw out the original liquid, mist droplets straightdiameter15~75μm④smoke spraying method: the use of high-temperature air flow to make the preheated smoke agent undergo thermal fission to form smoke, which is then blown away by the air flow to make the mist droplets straightdiameter1~50μm.

⑤electrostatic spray method: the liquid in the atomization process with electrostatic charge, the formation of charged droplets.

⑥powder spraying method: the use of high-speed air flow to spray powder onto crops.

universal nozzle

1.Impact sprayHead---sprayGunatomization principle: high-pressure liquid through the nozzle to the outlet, due to the water section gradually reduced, the flow rate gradually increased, the pressure is gradually reduced, the formation of high-speed liquid column shot to the distance.

2.features: atomization force difference, droplet diameterin300microns, but the range is long, often used in garden spray medicine.

3.Vortex Nozzleatomization principle:When the high-pressure liquid medicine enters the tangential chute of the nozzle from the liquid inlet pipe, the cross-sectional area of the chute becomes smaller, so the pressure drops and the flow rate increases. The liquid medicine enters the vortex chamber at a higher tangential speed and makes a high-speed spiral motion around the cone core in the nozzle body. Due to the combined effect of the centrifugal force generated by the rotating motion and the pressure difference between the inside and outside of the nozzle, the liquid medicine will form a twisted conical liquid after passing through the nozzle, that is, it becomes a hollow cone, which collides with relatively still air to form fine droplets and spray them on crops.

4.fan-type fog sprayHeadatomization: When the pressure liquid medicine enters the nozzle, the liquid medicine is divided into two relatively weighed liquid flows by the guiding effect of the bottom of the inner half-moon groove. The two flows to the nozzle hole and merge, collide with each other, and are finely broken into mist. Droplets are sprayed out. After the ejection, it collides with the two side walls of the half-moon groove, finely fragments and restraints, as well as the guiding effect of the bottom of the outer half-moon groove, forming a fan-shaped mist jet. At the same time, it collides with the relatively static air and further crumples it into droplets that are sprayed on the crops..

2.air chamber

Function: Eliminate the pulse phenomenon of the reciprocating pump, accumulate and stabilize the pressure to ensure the normal operation of the sprayer.

cultivator machinery

1.Common Coping Mechanism

profiling mechanism: make the working parts adapt to the terrain and maintain a certain depth of tillage.

1.single-lever single-hinge copying machinestructurecharacteristics: whether it is the change of soil resistance or the change of topographic relief, it can not guarantee the stable ploughing depth.

2.parallel four-bar profiling machinestructure(1) The ploughing depth and the penetration angle of working parts are relatively stable, and the copying amount is large.(2) copying allergy: when the copying wheel encounters local surface undulation (such as hard soil clods, ridges, etc.), the parallel four-bar copying mechanism will cause the working parts to jump, resulting in unstable ploughing depth and uneven ditch bottom. the phenomenon is called"profilingSensitive".(3) Profiling lag: In order not to interfere with the movement of the profiling wheel and the soil raised by the working part, the profiling wheel is usually arranged at a certain distance in front of the working part, thus causing the profiling of the working part to always lag behind the profiling wheel, formingis called"profiling hysteresis".

3.Multi-bar double-degree-of-freedom profiling machinestructurefeatures: large amount of profiling, stable work, gentle movement, but complex structure.

harvesting machinery

1.Construction and Working Process of Traditional Union

1.structuremadeis composed of header, conveying device, threshing device, cleaning device, separation device, engine, chassis, transmission system, electrical system, hydraulic system, cab and grain tank.

2.working process


2.the use of reciprocating cutter adjustment

1.levelwholepurpose: to ensure that each blade is in a plane, easy to ensure the gap.

adjustment method: knock the tip of the blade protector up and down with the head for correction. Note that the knife bar should be checked for straightness before correction.

2.Centering Adjustmentpurpose: to make good use of its speed. If the alignment is not adjusted properly, it is easy to block the knife, plug the knife or vibrate too much.

adjustment method: loosen the connecting rod bolt, adjust the length of the connecting rod or the position of the swing rod.

3.clearance adjustmentwholePurpose: To ensure the clearance between the moving knife and the fixed knife, the moving knife and the press required for normal cutting. Avoid due to improper clearance, easy to produce the crop uprooted, clogging or wear too fast and so on.

adjustment method: by adjusting the friction plate, increasing or decreasing the adjustment gasket and correcting the blade protector and press the blade.

calculation problem:


3.reel:

role:1.guide the crop to be cut towards the cutter and hold the fallen stemis;

2.support stem when cuttingRod;

3.push the cut grain to the inside so that the stalks don't pile up on the cutter.

adjustment:1. Position adjustment

includes up and down, front and rear position adjustment. Should be based on crop growth.

position adjustment are:

①tall stalk crops: increase before moving;②low stalk: lower after moving;

③Front side voltage: lower before moving.;④: lower after moving;

2. Speed adjustment

In most cases, it is also based on crop growth and maturity.

its adjustment principle is:

(1)Vm↑mentionhigh,nincrease,Vmreduction,nreduction. The aim is to maintain a certainλvalue.

(2) crop upright,ncan be lower, crop lodging,ncan be higher.

3. Inclination angle adjustment of spring teeth of eccentric reel

can change the angle of the elastic teeth relative to the ground by adjusting the eccentricity.

(1) Upright crops: Bounced vertically or slightly backward

(2) Forward crop: Teeth Tilt Back

(3) After the crop: elastic teeth forward (this situation should be avoided as far as possible)

threshing unit

1.threshing principle

1.impact threshing: using a threshing element with a certain speed to impact the grain and make the grain fall off.

2.Kneading and threshing: It uses the friction between the grain and the threshing element and between the grain to peel off the grain.

3.brush threshing: the threshing element exerts a pulling force on the grain, destroying the natural coupling force between the grain and the cob and causing it to fall off.

4.crushing and threshing: the use of threshing elements to squeeze the grains and make them fall off.

5.vibration threshing: The use of high-frequency vibration of grains to destroy the coupling force between grains and spike stalks to make them fall off. (Under study)

2. can be divided into two types according to whether the crops pass through the threshing device: full feeding type and half feeding type.

The full-feed threshing device is divided into two types according to the direction of movement of crops along the drum: shear flow and axial flow..

1.grain bar drum type threshingSetfeatures: high threshing speed, short action time on crops. It is mainly threshed by kneading and impact, and has low requirements for stems and high productivity. However, the concave plate has low separation rate and high power consumption.

2.Nail tooth drum threshingSetfeatures: mainly the use of impact and brush action threshing materials. The remaining features are the same as the grain bar type.

3.axial flow drum threshingSetcharacteristics: Threshing speed is low, the role of crops for a long time. It is mainly used for threshing by kneading. The requirements for stems are not high, the separation area of the concave plate is large, the separation rate is high, and the productivity is high. However, the stem is severely broken, the power consumption is high, and the transmission design is complicated.

Semi-feeding threshing device

1.Bow tooth drum threshingSetFeatures: low threshing speed, low impact effect, mainly using comb and brush action for threshing, high requirements for stems, low productivity, high entrainment loss, and low power consumption

2.before cutting offgrainfeatures: The machine only works on the ear head part, and does not harvest the stem at the same time, which solves the problem of high feeding requirements and greatly reduces the power consumption.

3. threshing unit

1.Speed adjustment: The V-belt stepless speed change method is generally used.

2.Clearance adjustment: The manual nut adjustment method is used to analyze and adjust on the thresher, and the linkage lever method is used on modern combine harvesters, which is convenient and rapid.

Drum speeddegreesV↑concave plate separationrate↑, not taken offrate↓, crushed stemsRod↑, grain brokenbroken↑.Vis generally obtained by looking up tables or empirical formulas.

The inlet clearance of the general threshing device is about the outlet clearance3~4times, wheat: inlet clearance16~22mm, export4~6mm.

cleaning device

1. are separated according to grain size characteristics

1.by grain widthdegreesseparation by width is carried out with a round mesh screen. The diameter of the sieve is less than the length of the grain and greater than the thickness of the grain. When separating, the grain can pass through the sieve as long as it can stand up, so the length and thickness are not limited by the sieve.

2.by grain thicknessdegreescommon method is to use a long hole sieve. The width of the long mesh screen is greater than the grain thickness and less than the grain width, and its length is greater than the grain length. At this time, the grain needs to be erected to pass through the sieve, and the sieve only needs to be vibrated horizontally.

3.according to grain length sizefromgrain selectioncylinder(also known as the nest eyecylinder)carried out

Fan

1. vane fan type and application range

According to the working principle of the fan, it can be divided into two types: axial fan and centrifugal fan.

axial fan wind pressure is low, the flow is large, generally used for ventilation, ventilation.

centrifugal fan wind pressure is higher, the use is very extensive.

centrifugal fan according to the structure type can be divided:

①clear graintype

features: large width, straight blade, round shell, used for clearing grain;

②General Purpose

features: small width, volute shell, for the need for medium and high pressure wind pressure field

Press wind pressurepointslow pressure: wind pressure<100mmH2;medium pressure: wind pressurein100~300 mmH2O; high pressure:300~1500 mmH2O

Generally, the grain cleaning fans are mostly low-pressure fans, and medium and high-pressure fans are used for sowing, plant protection and airflow transportation.

Corn Harvesting Machinery

1. corn ear picker

According to the structure, the ear picker can be divided into vertical horizontal picking roller, vertical picking roller, horizontal picking roller and vertical picking plate four kinds.

在线培训

Created on:2024-09-01

(full version) summary of agricultural machinery knowledge points

plough

1. are divided into traction plow, suspension plow and semi-suspension plow according to different ways of coupling with tractor.

1. Tractionploughstructure: it is mainly composed of traction device, plough frame, plough wheel, plough body, small front plough, round plow blade, lifting mechanism and adjusting mechanism.

Features:①the longitudinal size of the plow body is not limited, so more plows can be configured..②complex structure, heavy weight.

③large turning radius.④metal consumption, high price.

2. SuspensionploughStructure: The suspension plow is much simpler than the traction plow structure. It is generally composed of a plow frame, a suspension frame, a main plow body, a plow blade, an adjusting device and a depth limiting wheel.

Features:①strong maneuverability, flexible turning.②metal consumption is small, light weight, low cost.

③on tractor driving wheel weight gain effect is good.

3. semi-suspendedploughStructure: The front end of the plough is suspended by the tractor, and the rear end is the depth limiting wheel and tail wheel mechanism. Its structure is composed of the first two parts respectively.

Features:①weight is lighter than traction plowabout1/3, but the longitudinal size of the plough is not limited.;②is better than that of traction plow.

4. Turning plow (two-way plow)

turning plough is divided into left turning, right turning and horizontal turning. Its main advantages are: leveling the surface after ploughing, reducing the empty stroke of the ground head and improving work efficiency.

2.tillage soil ratioresistanceKt: Longitudinal horizontal resistance per unit cross-sectional area of soil during ploughing under standard conditions.

The so-called standard operating conditions, refers to the use of standard plough body, in the commonly used tillage depth range, commonly used tillage speed and suitable tillage water time to measure the force, calculated.outKt.

plowing soil specific resistance comparison intuitively discriminates the difficulty of plowing soil.

3. main plough body

function: cut, break, flip the soil, in order to achieve the purpose of covering weeds and residual roots, loose soil.

composition: composed of ploughshare, plough wall, plough side plate, plough heel, plough column, etc. Some plows have extension plates in order to strengthen the turning effect of the plow..

4. plough side plate

plough is located at the rear of the plough, which bears and balances the side pressure generated by the plough body during work to ensure the stability of the plough width. The side plate of the last plow of the multi-share plow is the most stressed and worn out, and is generally equipped with a replaceable plow heel.

①plough side plate in horizontal plane

in order to make the reaction force of the ditch wall act on the rear end of the plough side plate to increase the plough width stability. The front end of the side plate should be separated from the trench wall line, that is, there is a certain horizontal gap, and its value is generally5~10mm.

②Configuration of Plough Side Plate in Vertical Plane

the distance between the front end of the plough side plate and the bottom plane of the trench is called the vertical gap.

vertical gap reduces the reaction force of the soil to the side plate of the plough, so that the depth limiting wheel of the plough bears a certain supporting reaction force, so that the plough depth remains stable; at the same time, the soil clearance angle is increased to facilitate the plough into the soil. General vertical clearance10~20mm.

5. the process of turning over the soil (drawing)

in the work, the plough plow out of the rectangular soil. where the share blade cuts out its widthdegreesB, shin blade cut out its depthdegreesa. There are three modes of movement of the soil on the surface of the plow: rolling, rolling and rolling. In the northern general-purpose plough in the form of rolling.

in the study of soil movement process, there are three assumptions:

①soil section remains unchanged during the overturning process and is always rectangular;

②The soil strip is not broken;

③turnover.

6. height adjustment unit:is working, the hydraulic system of the tractorin"floatmovement"state, the plowing depth is controlled by the depth limiting wheel.

7. lead curve: the ripe plough body is required to have better soil crushing performance, and the lead curve is set at a distance from the plough.tip2/3on the plane of the plough.the half-spiral (turning-up) plow body, it is located at the end of the share.

For the lead curve with the same opening, the closer the position is to the tip, the better the soil crushing performance, on the contrary, the better the soil turning performance.

8. produce four different traction states according to the different positions of instantaneous center, resistance center and power center:

positive traction:π2is located on the center line, and the traction line passes through the power center line.

partial traction:π2is located on the right side of the centerline, and the traction line is parallel to the forward direction of the unit, but is in line with the powerHeartCdeviation distancefrome.

Oblique traction:π2is located to the left of the center line, but the traction line passes through the power center line.

skew traction: instantaneousHeartπ2is uncertain, but the pull line is neither through the power.HeartC, it is also not parallel to the direction of advance.


9. partial traction phenomenon: any traction line does not pass through the power center and causes the deflection torque of the unit, which makes the tractor produce automatic deviation, is called partial traction phenomenon.

(1) Essence of partial traction adjustment

by adjusting the position of the lower suspension point relative to the plow frame, to changechangeπ2the position, so as to change the direction of the pull wire, in order to eliminate or reduce the deflection moment.

note: in the adjustment should keep the tillage width unchanged, should look after each other.

(2) Adjustment Method

①first shift the suspension shaft (only the left and right suspension points can be moved on the plow equipped with the plow width adjuster) to make the traction line pass through the power center, thus forming the oblique traction phenomenon.

②the adjustment may cause the ploughshare deflection, the deflection can be eliminated by changing the front and rear positions of the lower suspension point.

10. traction plough

1.ploughing depth adjustment

operation, according to the requirements of ploughing depth, timely rotate the ploughing depth adjustment wheel, shorten the length of the lead screw when the ploughing depth becomes shallow, otherwise the ploughing depth becomes deep. If the plow is controlled by hydraulic pressure, different positions of the positioning baffle on the piston rod can be changed to obtain different tillage depth, while the upward movement increases the tillage depth and the downward movement becomes shallow.

2.horizontal adjustment

operation, it is required that the frame should be parallel to the ground plane to make the ploughing depth of the left and right ploughs consistent, otherwise, the horizontal adjustment wheel should be rotated to adjust.

3.Tail Wheel Adjustment

: ensure that the depth of the last plough is the same as that of the first plough. If not, adjust the vertical adjustment screw, screw in, after the end of the shallower, on the contrary, deeper.

horizontal adjustment: mainly to adjust the side pressure of the plough side plate and tail wheel. When the horizontal adjustment screw is screwed in, the tail wheel moves in the direction of uncultivated land, and vice versa.

4.Adjustment of traction linewhole

(1) Adjustment of traction lineaccordingresistance center theory (United States, Western Europe); centroid theory (former Soviet Union, Eastern Europe)

(2) Principles and methods of adjustmentlawtraction line adjustment: the traction line must pass through the resistance center or the center of gravity of the plowtraceSpoint and keep parallel to trench wall

XI. Consequences of Improper Position of Traction Wire

In the horizontal plane:

traction line deviates to the right: the plow frame is twisted counterclockwise, the total tillage width is narrowed, heavy tillage occurs between the ploughs, and the soil is not turned well..

traction line deviates to the left: the total tillage width becomes wider, there is leakage between the plough bodies, the surface is uneven after ploughing, the soil is not broken well, and the side surface of the plough side plate is severely worn.

common point is that the plow wheel inclines, which aggravates the wear of the axle sleeve and axle and increases the resistance.

In vertical plane:

The traction line is too high: the front part is lowered, the rear part is tilted, the load of the ground and groove wheels is aggravated, the axle is worn seriously, the front plow is deep and the rear is shallow.

traction line is too low: the front part of the plow frame is raised, the grasping force of the ground wheel is reduced, the lifting fails, the wear of the tail wheel axle is aggravated, and the front shaft is shallow and the rear shaft is deep.

disc harrow

1.disc harrow: used for crushing soil after ploughing, raking before sowing, and shallow tillage after harvesting.

2.classification:

1.according to the arrangement: single row rake, double row rake; opposed type, offset type

2.by weight:light (rake straightdiameter460mm), Medium(560mm), heavy(660mm)

3.divided by hooking method:Traction type, suspension type, semi-suspension type, etc.

3.rake deflection angle: refers to the angle between the rotation plane of the rake and the forward direction of the machine under working conditions.

4.disc harrow:1.rake group:1) Rakepiece2)partyshaft3)roomtube4)shaftBearing5) Scraping plate

2.Rake

3. Angle adjuster:(1) workusedchanging the size of the angle of each rake group to change its working depth,, the larger the contact area between the concave surface of the disc and the soil, and the greater the pressure of the soil on the concave surface of the disc, thus increasing the rake depth. On the contrary, the rake depth becomes shallow.

(2) groupangle adjuster is composed of upper and lower sliding plates, tooth plates, clips, supporting plates, front pull rods, rear center pull rods, etc.

4.Weight box, weight plate

5.transport wheel

6.Main Tunewhole

depth and light tonewhole(1)the deflection angle is increased, the depth of penetration increases, otherwise it becomes shallower.

(2)the weight is added to the weight plate and the weight box, the weight will become deeper when the weight increases, otherwise it will become shallower.

Sowing Machinery

1. seed treatment methods:1.seed pointslevel2.pellets3.offvelvet4.seed coating

2. laying film seeding mechanical composition:


1.Shaperstructure

function: push away the surface dry soil, press out the compact membrane bed, and open the membrane edge small ditch at the same time.

composition: including soil dividing plate (haveVtype) and shaping rollers (cylindrical and drum-shaped).

2.Fertilization institutions

Common forms of furrow opener: hoe shovel type, sliding force type, single disc type, etc..

3.Laying Mechanism

function: complete the operations of film spreading, film laying, film pressing and soil covering.

composition: including film roller, film spreading roller, film pressing wheel, earth disc, etc. The film spreading roller is a cylindrical or drum waist-shaped shaft. There are two types of film pressing wheels: integral type and separate type.

4.seeding mechanism

function: complete the seed arrangement under the membrane or on the membraneindustry

1)broadcastUsed for seeding under the film, the main working parts are the outer grooved wheel seeder and the double disc opener.

2) pointbroadcastis used for under-film or on-film seeding, and the main working part is the sowing wheel.

5.hole covering mechanism

function: cover and suppress the seed holes that have been sown.

3. outer sheave seeder

structure:

Leak-proof:


(1) Front wall inclinationangleα1should be greater than the seed's natural angle of repose.

(2) The seed passage should be wide and narrow, so that the seeds can easily fill the seed cup, and at the same time, it is not easy to flow.

(3) Seed tongue lengthdegreesm = 22~26mm, opendegreesCk =6~8mm, big seeds can be bigin10, small seeds can be smallin6, the angle should be less than the natural repose angle of the seed to prevent the seed from flowing.

4. air suction type seed meter

Seed disc structure parameters

①straightdiameterd: usually minussmalld,inυma certain time, can be reducedlowυp, is conducive to the absorption of species, reduce the leakage of sowing, but will make the organization large, air consumption also increased, so the current domestic and foreign more.usedd=140~260mmdisc.

②Suction hole diameter and shape: The shape of the suction hole is mostly circular, and burrs should be removed. The diameter is determined according to the size of the planted crop seeds. Jadem5~6mm, largebeans4~5mm, sweet pelletsdish2~3mm.

③Number and arrangement of suction holes

there are many suction holes, the spacing between adjacent suction holes is small, which is easy to absorb redundant seeds. At the same time, there is more air leakage, which requires more air volume. It is better to have a little more without affecting the suction, scraping and dropping of seeds. The arrangement of suction holes includes single row, staggered double row, hole group, thin strip hole and inclined seam.

Plant Protection Machinery

1.application

①spray method: the pressure liquid is atomized through the nozzle, and the droplets are straightdiameter100~300μm.

②Mist method: the use of high-speed air flow will be coarse fog droplets broken, blowing, fog droplets straightdiameter75~100μm.

③Ultra-low volume spray method: the use of high-speed rotating disc generated by the centrifugal force to throw out the original liquid, mist droplets straightdiameter15~75μm④smoke spraying method: the use of high-temperature air flow to make the preheated smoke agent undergo thermal fission to form smoke, which is then blown away by the air flow to make the mist droplets straightdiameter1~50μm.

⑤electrostatic spray method: the liquid in the atomization process with electrostatic charge, the formation of charged droplets.

⑥powder spraying method: the use of high-speed air flow to spray powder onto crops.

universal nozzle

1.Impact sprayHead---sprayGunatomization principle: high-pressure liquid through the nozzle to the outlet, due to the water section gradually reduced, the flow rate gradually increased, the pressure is gradually reduced, the formation of high-speed liquid column shot to the distance.

2.features: atomization force difference, droplet diameterin300microns, but the range is long, often used in garden spray medicine.

3.Vortex Nozzleatomization principle:When the high-pressure liquid medicine enters the tangential chute of the nozzle from the liquid inlet pipe, the cross-sectional area of the chute becomes smaller, so the pressure drops and the flow rate increases. The liquid medicine enters the vortex chamber at a higher tangential speed and makes a high-speed spiral motion around the cone core in the nozzle body. Due to the combined effect of the centrifugal force generated by the rotating motion and the pressure difference between the inside and outside of the nozzle, the liquid medicine will form a twisted conical liquid after passing through the nozzle, that is, it becomes a hollow cone, which collides with relatively still air to form fine droplets and spray them on crops.

4.fan-type fog sprayHeadatomization: When the pressure liquid medicine enters the nozzle, the liquid medicine is divided into two relatively weighed liquid flows by the guiding effect of the bottom of the inner half-moon groove. The two flows to the nozzle hole and merge, collide with each other, and are finely broken into mist. Droplets are sprayed out. After the ejection, it collides with the two side walls of the half-moon groove, finely fragments and restraints, as well as the guiding effect of the bottom of the outer half-moon groove, forming a fan-shaped mist jet. At the same time, it collides with the relatively static air and further crumples it into droplets that are sprayed on the crops..

2.air chamber

Function: Eliminate the pulse phenomenon of the reciprocating pump, accumulate and stabilize the pressure to ensure the normal operation of the sprayer.

cultivator machinery

1.Common Coping Mechanism

profiling mechanism: make the working parts adapt to the terrain and maintain a certain depth of tillage.

1.single-lever single-hinge copying machinestructurecharacteristics: whether it is the change of soil resistance or the change of topographic relief, it can not guarantee the stable ploughing depth.

2.parallel four-bar profiling machinestructure(1) The ploughing depth and the penetration angle of working parts are relatively stable, and the copying amount is large.(2) copying allergy: when the copying wheel encounters local surface undulation (such as hard soil clods, ridges, etc.), the parallel four-bar copying mechanism will cause the working parts to jump, resulting in unstable ploughing depth and uneven ditch bottom. the phenomenon is called"profilingSensitive".(3) Profiling lag: In order not to interfere with the movement of the profiling wheel and the soil raised by the working part, the profiling wheel is usually arranged at a certain distance in front of the working part, thus causing the profiling of the working part to always lag behind the profiling wheel, formingis called"profiling hysteresis".

3.Multi-bar double-degree-of-freedom profiling machinestructurefeatures: large amount of profiling, stable work, gentle movement, but complex structure.

harvesting machinery

1.Construction and Working Process of Traditional Union

1.structuremadeis composed of header, conveying device, threshing device, cleaning device, separation device, engine, chassis, transmission system, electrical system, hydraulic system, cab and grain tank.

2.working process


2.the use of reciprocating cutter adjustment

1.levelwholepurpose: to ensure that each blade is in a plane, easy to ensure the gap.

adjustment method: knock the tip of the blade protector up and down with the head for correction. Note that the knife bar should be checked for straightness before correction.

2.Centering Adjustmentpurpose: to make good use of its speed. If the alignment is not adjusted properly, it is easy to block the knife, plug the knife or vibrate too much.

adjustment method: loosen the connecting rod bolt, adjust the length of the connecting rod or the position of the swing rod.

3.clearance adjustmentwholePurpose: To ensure the clearance between the moving knife and the fixed knife, the moving knife and the press required for normal cutting. Avoid due to improper clearance, easy to produce the crop uprooted, clogging or wear too fast and so on.

adjustment method: by adjusting the friction plate, increasing or decreasing the adjustment gasket and correcting the blade protector and press the blade.

calculation problem:


3.reel:

role:1.guide the crop to be cut towards the cutter and hold the fallen stemis;

2.support stem when cuttingRod;

3.push the cut grain to the inside so that the stalks don't pile up on the cutter.

adjustment:1. Position adjustment

includes up and down, front and rear position adjustment. Should be based on crop growth.

position adjustment are:

①tall stalk crops: increase before moving;②low stalk: lower after moving;

③Front side voltage: lower before moving.;④: lower after moving;

2. Speed adjustment

In most cases, it is also based on crop growth and maturity.

its adjustment principle is:

(1)Vm↑mentionhigh,nincrease,Vmreduction,nreduction. The aim is to maintain a certainλvalue.

(2) crop upright,ncan be lower, crop lodging,ncan be higher.

3. Inclination angle adjustment of spring teeth of eccentric reel

can change the angle of the elastic teeth relative to the ground by adjusting the eccentricity.

(1) Upright crops: Bounced vertically or slightly backward

(2) Forward crop: Teeth Tilt Back

(3) After the crop: elastic teeth forward (this situation should be avoided as far as possible)

threshing unit

1.threshing principle

1.impact threshing: using a threshing element with a certain speed to impact the grain and make the grain fall off.

2.Kneading and threshing: It uses the friction between the grain and the threshing element and between the grain to peel off the grain.

3.brush threshing: the threshing element exerts a pulling force on the grain, destroying the natural coupling force between the grain and the cob and causing it to fall off.

4.crushing and threshing: the use of threshing elements to squeeze the grains and make them fall off.

5.vibration threshing: The use of high-frequency vibration of grains to destroy the coupling force between grains and spike stalks to make them fall off. (Under study)

2. can be divided into two types according to whether the crops pass through the threshing device: full feeding type and half feeding type.

The full-feed threshing device is divided into two types according to the direction of movement of crops along the drum: shear flow and axial flow..

1.grain bar drum type threshingSetfeatures: high threshing speed, short action time on crops. It is mainly threshed by kneading and impact, and has low requirements for stems and high productivity. However, the concave plate has low separation rate and high power consumption.

2.Nail tooth drum threshingSetfeatures: mainly the use of impact and brush action threshing materials. The remaining features are the same as the grain bar type.

3.axial flow drum threshingSetcharacteristics: Threshing speed is low, the role of crops for a long time. It is mainly used for threshing by kneading. The requirements for stems are not high, the separation area of the concave plate is large, the separation rate is high, and the productivity is high. However, the stem is severely broken, the power consumption is high, and the transmission design is complicated.

Semi-feeding threshing device

1.Bow tooth drum threshingSetFeatures: low threshing speed, low impact effect, mainly using comb and brush action for threshing, high requirements for stems, low productivity, high entrainment loss, and low power consumption

2.before cutting offgrainfeatures: The machine only works on the ear head part, and does not harvest the stem at the same time, which solves the problem of high feeding requirements and greatly reduces the power consumption.

3. threshing unit

1.Speed adjustment: The V-belt stepless speed change method is generally used.

2.Clearance adjustment: The manual nut adjustment method is used to analyze and adjust on the thresher, and the linkage lever method is used on modern combine harvesters, which is convenient and rapid.

Drum speeddegreesV↑concave plate separationrate↑, not taken offrate↓, crushed stemsRod↑, grain brokenbroken↑.Vis generally obtained by looking up tables or empirical formulas.

The inlet clearance of the general threshing device is about the outlet clearance3~4times, wheat: inlet clearance16~22mm, export4~6mm.

cleaning device

1. are separated according to grain size characteristics

1.by grain widthdegreesseparation by width is carried out with a round mesh screen. The diameter of the sieve is less than the length of the grain and greater than the thickness of the grain. When separating, the grain can pass through the sieve as long as it can stand up, so the length and thickness are not limited by the sieve.

2.by grain thicknessdegreescommon method is to use a long hole sieve. The width of the long mesh screen is greater than the grain thickness and less than the grain width, and its length is greater than the grain length. At this time, the grain needs to be erected to pass through the sieve, and the sieve only needs to be vibrated horizontally.

3.according to grain length sizefromgrain selectioncylinder(also known as the nest eyecylinder)carried out

Fan

1. vane fan type and application range

According to the working principle of the fan, it can be divided into two types: axial fan and centrifugal fan.

axial fan wind pressure is low, the flow is large, generally used for ventilation, ventilation.

centrifugal fan wind pressure is higher, the use is very extensive.

centrifugal fan according to the structure type can be divided:

①clear graintype

features: large width, straight blade, round shell, used for clearing grain;

②General Purpose

features: small width, volute shell, for the need for medium and high pressure wind pressure field

Press wind pressurepointslow pressure: wind pressure<100mmH2;medium pressure: wind pressurein100~300 mmH2O; high pressure:300~1500 mmH2O

Generally, the grain cleaning fans are mostly low-pressure fans, and medium and high-pressure fans are used for sowing, plant protection and airflow transportation.

Corn Harvesting Machinery

1. corn ear picker

According to the structure, the ear picker can be divided into vertical horizontal picking roller, vertical picking roller, horizontal picking roller and vertical picking plate four kinds.