agricultural machinery
large, medium and smallagricultural machineryBasics
tractor
1. tractors
1.Tractors classified by use
tractors can be divided into two categories according to their uses, agricultural and public, and agricultural tractors can be divided into two types according to their uses.:1.General-purpose tractors are used for field ploughing, harrowing, sowing, harvesting and other operations..2.Special purpose tractors are used for special agricultural working conditions, such as intertillage tractors, cotton field high and low clearance tractors, and skim tractors.
2.Tractors are classified according to their structure
tractors are divided into walking tractors, wheeled tractors, crawler tractors, boat tractors, etc. according to their structure.
3.by power size
Large tractor power73.6kW (namely100horsepower) or more; medium-sized tractor powerrate14.7~73.6kW (namely20~100horsepower); small tractor power14.7kW (namely20horsepower) below.
2. tractor
tractor is mainly composed of three parts: engine, chassis and electrical equipment.
secondengine
Engine type and basic structure
engine is the power unit of the entire tractor, and it is also the most important and critical part of the tractor to provide power for the tractor. All devices that convert some form of energy into mechanical energy become engines. Engines can be divided into wind engines, water conservancy engines, and heat engines due to different energy sources. In-line, water-cooled, multi-cylinder four-stroke diesel engines widely used in large and medium-sized tractors.
1. basic structure
diesel engine is composed of many institutions and components, according to its function can be divided into the main system and auxiliary system.
The main system includes: crank connecting rod mechanism and body parts, valve mechanism and intake and exhaust systems, and fuel supply system.
auxiliary system includes: lubrication system, cooling system, and starting system.
2. diesel engine
Every time a diesel engine completes a working cycle, it goes through four strokes: air intake, compression, work, and exhaust. The piston reciprocates up and down twice, and the crankshaft makes two revolutions.
1.Intake stroke
The crankshaft rotates by the inertial force of the flywheel, driving the piston to move from top dead center to bottom dead center. At this time, the exhaust valve is closed and the intake valve is opened. As the cylinder volume increases, a pressure difference between the inside and outside is formed, and fresh air is sucked into the cylinder.
2.compression stroke
The crankshaft continues to rotate by the inertial force of the flywheel, driving the piston to move from bottom dead center to top dead center. At this time, the intake and exhaust valves are closed, and a sealed space is formed in the cylinder. As the gas is compressed, the pressure and temperature continue to rise. Before reaching the top dead center, the injector injects high-pressure diesel into the combustion chamber.
3.Work stroke
the intake and exhaust valves are still closed, the temperature in the cylinder reaches the diesel auto-ignition temperature, which causes the diesel to burn and release heat energy. The high-temperature and high-pressure gas expands sharply, pushing the piston to move from top dead center to bottom dead center to do work, and driving the crankshaft through the connecting rod Rotate to output power outward.
4.Exhaust stroke
Under the action of the inertial force of the flywheel, the rotating crankshaft drives the piston to move from bottom dead center to top dead center. At this time, the intake valve is closed and the exhaust valve is opened. Since the exhaust gas pressure is higher than the external atmospheric pressure, and at the same time, under the push of the piston, the working exhaust gas is discharged from the exhaust valve.
3. crank connecting rod mechanism and body parts
1.crank connecting rod mechanism
crank connecting rod mechanism is the main mechanism of diesel engine energy conversion. When the diesel engine is running, the chemical energy of the fuel is converted into energy through combustion, and then the reciprocating linear motion of the piston is converted into the rotational motion of the crankshaft through the crank connecting rod mechanism, and external work is performed in the form of torque.
The crank connecting rod mechanism is mainly composed of the following components;
The connecting rod group includes pistons, piston rings, piston pins, connecting rods and other moving parts.
Cylinder block: The crankcase group includes cylinder block, crankcase, cylinder head, cylinder head gasket and other fixed parts.
Crankshaft: The flywheel group includes moving parts such as crankshaft and flywheel.
4. body parts
Piston connecting rod group: The piston connecting rod group is mainly composed of piston, piston ring, piston pin, connecting rod, connecting rod cover, connecting rod bearing bush, connecting rod bolt, connecting rod bushing, etc.
1.Piston
The working conditions of the piston: The top of the piston forms a combustion chamber with the cylinder and the cylinder head. When working, it directly contacts the high-temperature gas, bears the gas pressure in the cylinder, and transmits this pressure to the connecting rod through the piston pin to push the crankshaft to rotate.
piston is divided into four parts: the top part, the groove part, the pin seat part and the skirt part.
: Since the top of the piston is a part of the combustion chamber, the shape of the top is related to the form of the combustion chamber.
return groove: above the piston ring groove2~3ring groove is the position for installing the gas ring, and the lower ring groove is used for installing the oil ring.
skirt: The part below the piston ring groove is the skirt of the piston, which plays a guiding role and bears side pressure.
2.piston ring
The piston ring is divided into two types: air ring and oil ring. They are installed in the ring groove of the piston, and rely on elastic force to cling to the cylinder wall, and move up and down with the piston.
The function of the gas ring: It is the seal between the weight-taking piston and the cylinder wall to prevent high-temperature and high-pressure gas from leaking into the crankcase, and transfer most of the heat from the top of the piston to the cylinder wall through the piston ring.
The function of the oil ring is to scrape off the excess lubricating oil on the cylinder wall and distribute the oil evenly.
Gas ring: In the free state, the gas ring is an open ring slightly larger than the inner cylinder. After it is installed in the cylinder together with the piston, it relies on its own elastic force to cling to the cylinder wall to play a sealing role.
3.piston pin
The function of the piston pin is to connect the piston and the connecting rod and transmit power. The piston pin and the pin seat generally adopt a floating connection, that is, when the engine is working, the piston pin can rotate freely in the pin seat and the small end bushing of the connecting rod, so that the wear is even and the service life is prolonged.
4.connecting rod
The function of the connecting rod group: The common function of the connecting rod group is to transmit the force of the piston to the crankshaft and convert the reciprocating linear motion of the piston into the rotational motion of the crankshaft.
The composition of the connecting rod group: The connecting rod group includes connecting rod, connecting rod cover, connecting rod small end bushing, connecting rod bolt, connecting rod bearing bush, etc.
Body Group
The body forms mainly include the following: The body group is mainly composed of body, cylinder liner, cylinder head, cylinder head gasket, oil pan and so on.
Section 1Basic driving knowledge and basic operation
1.Inspection and preparation before departure
(1)check whether there is enough water in the water tank, and add it when it is insufficient;
(2)check whether the height of the lubricating surface of the engine oil pan is within the normal height range, and add it appropriately when it is insufficient;
(3)check the gear, the gear should be in neutral;
(4)check whether the fuel in the diesel tank and the small gasoline tank of the starter is sufficient, and check whether the lubricating oil in the transmission fuel injection pump is sufficient;
(5)check whether there is oil leakage or water leakage in each pipeline system;
(6)check the fastening conditions of bolts and other fasteners of all important connecting parts;
(7)check whether the tire pressure is sufficient and the crawler tension of the crawler tractor;
(8)check whether the on-board tools and spare parts are complete;
(9)check whether electrical appliances, lighting and signal lamps are in good condition;
(10)does not use the hydraulic system and the power output shaft, set their operating handles separately.in"pointsfrom"location.
2.Tractor
After the engine is started, the car must be warmed up at a medium speed idling, and the oil pressure must be maintained.in147kPa, the water temperature rises40℃or so, the tractor can be started. To water temperature60℃, the tractor can start load work.
(1)to the end and put the gear lever in low gear.
(2)slowly release the clutch pedal, while slightly increase the throttle, so that the tractor starts smoothly.
(3)throttle should be based on the size of the tractor traction load.
(4)starts uphill, first step on the brake, then step on the clutch pedal, and engage low gear. Then use the hand accelerator to increase the accelerator, and slowly release the pedal of the actuator at the same time. When the clutch is partially engaged, slowly release the brake. At this time, the brake and the clutch pedal are in the process of releasing at the same time until the tractor starts to drive slowly.
(5)the operation method of starting downhill is basically the same as that of uphill, the difference is that the throttle should be appropriately smaller.
3.Tractor
Tractor variable speed can be achieved by controlling the throttle and resisting two ways. The former can achieve a small range of speed change, the latter speed change range.
When the tractor has a large traction load or starts, goes uphill, or passes through low-lying uneven roads, a low-speed gear is used to obtain a large traction; when the tractor is engaged in transportation operations or field operations with a small load, a high-speed gear can be selected to increase productivity.
shifting is divided into parking shifting and shifting while moving. The latter needs to master certain skills to achieve. If the operation is not skilled, it is easy to cause the phenomenon of gear hitting or failure to shift. Whenever you shift gears, you must first step on the clutch pedal to achieve gear shifting.
4.Tractor
The steering of the tractor in any case should be achieved in the process of deceleration, first reduce the throttle or shift to low gear, and then turn. The key points of turning are: when turning a big turn, the steering wheel turns slowly and returns to the right; when turning a small turn, the steering wheel turns quickly and returns to the right; turning the steering wheel must start before the tractor turns.
is turning, because the front and rear wheel tracks of the tractor do not overlap, pay attention to the inner wheel difference.
When the tractor is towing or hanging farm tools to turn, be sure to look forward and backward. When working in the field, the working parts of the agricultural tools must be raised above the surface before the steering operation of the tractor can be carried out. Due to the soft or slippery ground, the lateral adhesion between the ground and the front wheels is relatively small, so when the steering wheel is difficult to turn, you can step on the brake pedal on the steering side to assist the tractor in turning through unilateral braking.
5.Correct use of differential lock
Wheeled tractors are generally equipped with a differential lock. When the differential lock is engaged, the two driven gears of the final drive can be forced to rotate at the same speed, so that the two driving wheels can rotate at the same speed.
, when one of the driving wheels of the tractor is too deep in the soil and the tractor is unable to move forward, the other driving wheel is slipping better. In this case, the differential lock can be used. After the tractor walks out of the slip zone, the differential lock should be released.
6. Tractor
When reversing, use low speed. When encountering a raised area, you can increase the throttle appropriately. Once you cross the raised area, immediately reduce the throttle and reverse slowly
(1)When reversing and starting, pay special attention to slowly releasing the clutch pedal. During the reversing process, you must take care of it before and after, and pay close attention to whether there are personnel or obstacles.
(2)When reversing and hooking up agricultural machinery or reversing into storage, slow down by stepping on the clutch pedal to assist in the reversing process, and be ready to step on the brake pedal at any time.
(3)steering operation at the time of reversing is basically the same as the steering operation at the time of advancing.
Section IIField Driving Technology
field, also known as drill pipe, is a method of combining individual subjects such as moving the vehicle to the warehouse, straight and curved forward, and backward. The driving contents in the site include: site style driving, site turning and ramp starting.
1.site style driving
1.In-field pattern driving diagram and driving route map
tractor.because
--------------------------------------------------------------------------------
1, poor daily maintenance. For example, in the process of long-term use, it is not done in accordance with the instructions of each vehicle, that is, it is not maintained on time and according to the number; the purification of oil, gas and water is not strictly done, resulting in early wear of parts, and timely inspection and treatment after wear, so that the machine operates with disease.
2, improper use and operation. For example, violation of operating regulations, such as neutral sliding, serious long-term overload, high-speed starting, sharp turns without lifting farm tools, unnecessary emergency braking, etc. Use oil that does not meet the technical requirements.
3, repair and assembly in violation of regulations. For example, it is not adjusted according to the required data, the quality of the replaced parts is poor, or the matching size does not meet the specified requirements.
4, design and manufacturing defects. For example, in the design and manufacture, due to the limitations of objective conditions or technical errors, so that some models or parts have weak links, so that in use it is easy to cause wear and tear caused by failure.
How to deal with abnormal flameout of walking tractor-
--------------------------------------------------------------------------------
the driver of the walking tractor cannot turn off the accelerator in his seat, he must pull the speed control handle to turn off the engine.
the reasons for this phenomenon, one is the improper installation position of the throttle lever and the connecting plate assembly. When the throttle handle is in the minimum position, the speed control handle is just in the uppermost position; the other is the improper installation position of the throttle connecting plate (located at the lower left of the timing gear chamber cover), and its small head is upward or leftward, resulting in insufficient preload of the torsion spring. When the throttle handle is in the oil stop position, the connecting plate assembly does not have enough power to pull the speed control handle to the uppermost oil stop position, so the throttle cannot be closed.
The trick to install the throttle connecting piece: First, insert one end of the torsion spring into the small hole of the connecting piece, and put the torsion spring and the connecting piece on the assembly. Then pass the fastening bolt through the assembly and tighten it on the body. Then twist the torsion spring with your left hand, that is, apply a pre-tightening force to it, so that the small end of the connecting piece is at the lower leftabout15°position. Finally, tighten the bolts to fix the assembly.
Diesel Enginelaw
--------------------------------------------------------------------------------
diesel engine exhaust diesel steamgas(white) and water vapor (pale white) are collectively referred to as white smoke. The causes and elimination methods are as follows:
1. Pale white smoke
①diesel fuel. Elimination method: drain the water in the bottom of the fuel tank, diesel filter, fuel injection pump and other components of the diesel supply system. Prevention: Diesel needs to sinkDian24hours. Do not insert the oil into the bottom of the diesel barrel when refueling. Fuel tank cap damage or loss to match in a timely manner.
②cooling water leaks into the cylinder. Poor sealing of the cylinder head gasket or cracks at the bottom of the cylinder head, and the cooling water in the water jacket leaking into the cylinder will also cause water vapor to emit white smoke. It is necessary to find the leaking area and repair or replace the relevant parts. Prevention: First, the cylinder head bolts should be tightened diagonally to the specified value. Second, when installing the cylinder liner, the cylinder liner shoulder should be slightly higher than the cylinder plane. Third, add cooling water in time to prevent the cylinder liner from cracking.
2. White smoke
①winter temperatures are low. Due to the low temperature, some diesel failed to catch fire and emit white smoke. This white smoke disappears with the increase of engine temperature, which is normal and does not need to be excluded.
②diesel. The reasons are: the fuel injection pressure is too low, the fuel injector is seriously dripping, or the fuel injector pressure is adjusted too low, causing part of the diesel oil mist to fail to ignite and burn in the combustion chamber and emit white smoke. The situation should be distinguished, or replace the plunger assembly of the oil pump, or adjust the fuel injection pressure to the normal value, or disassemble the fuel injector to grind and repair the needle valve assembly. If it cannot be repaired, replace it.
How to maintain tractor travel systemsystem
--------------------------------------------------------------------------------
1. check and adjust the front wheel alignment. The front wheel of the tractor is too large and the toe is very small, which is easy to cause eccentric wear during walking. The main reason is that the front axle bearing and sleeve are deformed by impact, or the front axle telescopic sleeve fastening device is loose, which will cause the front wheel positioning angle to change, which will cause abnormal wear. Therefore, in the process of use, we must always check whether the positioning angle of the front wheel is moderate, and adjust the toe.
2. operate correctly and drive carefully. When the tractor is walking, it should be careful not to cross obstacles at high speed, and not to make sharp turns under heavy load; drive at low speed on high and uneven roads, and try to avoid emergency braking; when climbing with heavy load or driving on muddy roads, Do not make the walking system slip seriously.
pay 3. attention to the operating conditions. Tractor in low-lying paddy field operations, to try to avoid the car, after the car to take traction and implementation of the method to eliminate, must not use the method of increasing the throttle (black smoke) to make the walking system adjust idling. When working in dry land with sharp stubble and high stubble, it is necessary to prevent tires from being punctured and rotating shafts from being entangled by crop straw.
4. timely cleaning. After the tractor operation is finished, the sludge contaminated on the wheels and crawler should be removed (cleaned) in time to keep the walking system clean, especially the end face oil seal device of the roller should be cleaned, checked and maintained in time. In addition, also pay attention not to let oil, acid, alkali and other corrosive substances stain rubber tires.
5. maintain normal tire pressure and track tension. Before using the tractor, carefully check whether the tire pressure is normal (slightly higher during transportation and lower during field operations; slightly higher in winter and lower in summer) to avoid flat tires or flat tires. If the track is too loose or too tight, it is easy to cause accelerated wear of the track shoes, track shafts and wheels, so it is necessary to maintain a suitable degree of tension.
Emergency response in case of locomotive failurelaw
--------------------------------------------------------------------------------
recruit1Shake when starting the car in the morning
Because individual cylinders are not working well and the valve is not closed tightly, it canin3blockor4block and run at high speed for a while. If the hot car does not shake but the gear shift is not smooth, it may be that the fuel injection nozzle is uneven and needs to be inspected and cleaned.
recruit2I feel that the brakes are not as good as before.
when waiting for the red light to step on the brakes, can be effective.
recruit3Vehicle deviation
Increase the air pressure of the front wheel in the direction of deviation or decrease the air pressure of the tire in the other direction.
recruit4morning ignition found that the battery energy is insufficient, starting difficult
pour a bottle of hot water on the battery and turn off all electrical equipment, including the door., etc.510minutes, then drive and change the battery.
recruit5The door handle is loose or the key becomes tight and astringent.
open the front door, you will see a plastic cover on the side, open it and see a screw inside, loosen a few turns, you can pull out the lock cylinder from the outside, there is a cable buckle on the handle, adjust the tightness of the cable. The screws of the rear door are blocked with a sealing strip and opened by hand. Before installation, apply grease to the inside of the lock cylinder, so that the handles and locks on the door will be easily restored.
recruit6Fuel tank damage
When a motor vehicle is in use, especially when driving in areas with poor road conditions, damage to the fuel tank may occur. If it is found that the oil tank is leaking, the oil can be wiped clean, with soap or bubble gum coated in the oil spill, temporarily play the role of blockage. If there are conditions, with epoxy resin adhesive repair, the effect is certainly better.
recruit7oil pipe
When the oil pipe is broken, the broken place can be wiped clean, coated with soap, wrapped around the broken place of the oil pipe with a cloth strip or tape, tied tightly with iron wire, and then coated with a layer of soap.
recruit8Oil pipe broken
When the oil pipe is broken, a rubber or plastic pipe suitable for the diameter of the oil pipe can be found for sleeve connection. If the socket is not tight enough, both ends shall be tied tightly with iron wire to prevent oil leakage.
recruit9oil pipe joint
When a motor vehicle is used, if the engine oil pipe joint leaks, it is mostly caused by the unsealing of the oil pipe horn and the oil pipe nut. Cotton yarn can be wound around the lower edge of the horn, and then the oil pipe nut and the oil pipe joint can be tightened. Bubble gum or maltose can also be chewed into paste, coated on the seat of the oil pipe nut, and sealed after it is dried and solidified.
recruit10Inlet and outlet hoses are broken
is not broken, you can use a cloth coated with a layer of soap to wrap the leak. If the rupture is large, the rupture of the hose can be cut off, and a bamboo pipe or iron pipe can be set in the middle and tied tightly with iron wire.
recruit11fan belt broken
can tie the broken belt in series with iron wire or drive the car away by starting and stopping.
oil?because
--------------------------------------------------------------------------------
diesel engine compression system, incorrect piston assembly, damage to the gaskets at each connection of the body, and damage to the side wall of the oil housing are all reasons for excessive oil consumption.
1. When it is found that the oil is consumed too much, first check whether there is oil leakage at the connection between the body and the gear chamber cover, the large plate on the side of the row wheel, the rear cover, and the cover. In case of oil leakage, attention should be paid to observe whether the sealing gasket of each connection part is complete, and the damaged sealing gasket should be replaced. If the gasket is complete, check whether the connecting screws of each part are loose. Use a wrench to tighten the loose bolts to the specified torque. If the above parts are basically normal and the oil leakage is at the position of the frame, the oil shell should be inspected. The main inspection part is at the front end of the oil shell side on the same side as the traveling wheel. The machine base screw is loose, and the traveling wheel is pulled by the triangle belt. With the protectionThe angle iron of the frame that protects the oil shell will rub for a long time, and the oil shell will be worn through to form a gap and cause oil leakage.
The normal wear and tear caused by the long-term use of the 2. engine, or the abnormal wear and tear caused by improper maintenance, will cause the cylinder liner of the diesel engine to form longitudinal pull marks, and the cylinder diameter and piston side clearance will exceed the specified values, so that the supporting force of the piston ring will be correspondingly reduced., There is a phenomenon of unclean oil scraping. Or because the inner support torsion spring in the oil ring is disconnected at the opening position of the oil ring, the oil scraping is not clean and participates in the combustion, causing serious oil consumption symptoms, which is manifested as difficulty in starting the diesel engine and obvious blue smoke from the exhaust pipe., The respirator is injected seriously. In addition, the piston should be on the upward side. During assembly, the combustion chamber is inverted due to the inverted direction. Although it will not affect the starting of the diesel engine, the oil loss will be quite serious. The daily fuel consumption is0.5kg.
3. valve guides to burn engine oil due to severe wear, according to relevant information, it is also a reason that cannot be underestimated.
tractors are not safe to dolaw10example
--------------------------------------------------------------------------------
1. Operation under load without running-in and commissioning
the newly purchased or overhauled engine will be loaded without running-in and test run, which will cause serious wear of moving parts, which will cause the parts to lose their working ability and shorten the service life of the whole machine. In order to reduce the wear of parts in the initial stage, check and eliminate the problems existing in the manufacturing, repair and assembly of parts, and make the parts of the whole machine coordinate with each other, the newly purchased or overhauled engine should be in accordance with the corresponding regulations.Fan(The load is from small to large, the speed is from low to high, and the gear is from lowhigh)shall be run-in and test run, and then put into operation with additional load after inspection and adjustment. This can give full play to the mechanical efficiency, prolong the service life and prevent accidents.
2, smoking and one-handed direction control while driving a tractor
drivers are used to smoking while driving, on the grounds that smoking can relieve boredom. As everyone knows, smoking not only distracts the driver's attention, but also affects his line of sight. Smoke from smoking seriously irritates the eyes and throat, causing the operator to weep or cannot open it.Eyes.cough worsens. Especially when driving a walking tractor without a cab, smoking, soot and splashing sparks may all become hidden dangers of accidents. In addition, when working in the wheat field, smoking can easily lead to fire, causing losses to people's lives and property. Perhaps it is because of smoking and slapstick, or because the driver thinks that the operation level is high. People often see some drivers driving with one hand or using their feet to control the direction of the locomotive. You know, although the speed of the tractor is not fast, it is still a motor vehicle.Column;drivers are, they are not performing acrobatics. In case of an emergency, it is too late to regret an accident.
3, overloading and speeding mixed loading of people and goods
overloading and faster speed or Dora's fast running are concrete manifestations of the operator's eagerness to make money. Tractor overloading is very harmful, that is, it reduces the braking performance of the whole machine, and aggravates the wear of parts. Once the goods are not tightly bound or the road surface is bumpy, it is easy to have a rollover accident. If the speed is too fast, the safe braking distance will be longer, so the brake device is required to be more sensitive and the driver's response is more agile, so that it can stop quickly in an emergency. People and goods are mixed, and even in places where traffic conditions are backward, tractors have become a tool for pulling people and carrying passengers. This kind of operation seriously threatens the safety of people's lives and property and is an illegal act.
4, excessive fatigue driving
some drivers travel day and night during long-distance transportation, fighting fatigue, eating poorly, and sleeping poorly, which is very hard. This practice is not safe. Sleep is a normal physiological need. Drivers who do not get enough rest often cause traffic accidents due to confusion and drowsiness when driving, which is both harmful and harmful.
5, locomotive downhill neutral coasting
, when an object slides down a slope, the weight of the object will be decomposed into a component force along the downhill direction, and the object will be accelerated to make its sliding speed faster and faster. If no reaction force is given in the middle, the object will finally slow down and stop by friction resistance. If a resistance is suddenly applied to the object in the middle, the object is prone to roll over. The reason why the tractor is not allowed to slide downhill is the same.
6and troubleshooting
, some operators found that the tractor or supporting machine had a fault during the operation. For convenience, under the condition that the engine did not stall, they took the risk to eliminate the fault, resulting in personal injury and death accidents, and the loss outweighed the gain.
7and tractors shall not cut off the power of the operating machine when carrying out field transfer.
tractors do not cut off the power when transferring in the field, resulting in trenchers and rotary tillers blades, harvester cutters, planter openers, etc. being damaged or bruised when passing through hard fields, small ditches or other obstacles.
8and threshing operation, the operator leaves the post without permission.
busy season, some operators were tired after working overtime and continuous work, so during threshing work, he went to sleep by the haystack after turning on the machine. This kind of accident of threshing machine injury caused by the operator leaving the job is on the rise.
9, short-term parking, step on the clutch and do not shift gears
when driving, it is inevitable to stop and talk to relatives and friends. However, the practice of stepping on the clutch and not taking off the gear has potential factors that cause accidents. At the same time, this approach is also easy to increase the wear of the clutch and shorten the service life of the clutch.
10, bang the throttle before starting
tractor drivers always like to bang the throttle a few times before the locomotive starts to make the engine speed suddenly increase. This has the following disadvantagesDivision:①The engine speed changes suddenly, causing the valve spring and fuel injection pump plunger return spring to break due to resonance.②The engine speed changes dramatically, resulting in poor surface lubrication of friction parts and increased wear.③engine are subjected to excessive impact load and fatigue damage..④engine is greater than the valve return speed, causing the valve lock clip to fall off and the valve falling into the cylinder to cause an accident.
New Agricultural Machinery Use Four Notesmeaning
--------------------------------------------------------------------------------
1. buys a new machine, before using the engine, they must first carefully read the operating instructions of the machine, pay special attention to the use of the specified brand of fuel, fully precipitate and filter before use, and keep the oiler clean. The lubricating oil should be kept clean, the quantity added should be sufficient, and it should be replaced regularly. The use grade should be consistent with the regulations. Air filter should always pay attention to maintenance. Pay attention to adding cooling water, especially not to make the engine work in a state of water shortage. Always pay attention to check and tighten the relevant bolts and nuts, especially the connecting rod bolts, the bolts on the drive shaft, the lock nuts on the flywheel, and the fastening nuts of the wheels. If the user buys a new machine and really follows the basic requirements, then the life of the machine can be greatly extended.
2. after buying a new machine, do not immediately carry the load operation, should be in accordance with the requirements of the instructions for its trial run-in. After running-in, clean the oil filter screen of the machine and remove the residual impurities in the oil. If necessary, replace the oil and clean the oil pan.
When 3. the new machine for operation, it should be done in strict accordance with the requirements of the manufacturer's instructions, not overloading, not overspeeding, not overfeeding, not long-term overload work.
4. can not arbitrarily modify the new machine and arbitrarily increase the engine speed. In order to make the machine run faster, some users adjust the oil supply and pressure of the high-pressure oil pump at will, and some tie the speed regulating spring with iron wire, which is even more wrong.
replacement of agricultural machinery new accessories pay attention to thingsItem
--------------------------------------------------------------------------------
some operators believe that the replacement repair is very simple, the damaged parts installed on the line. In fact, it is not the case. If the assembly is improper, the power will be reduced, the fuel consumption will increase, and the starting will be difficult; if it is heavy, the machine will be damaged. Therefore, the replacement of new parts has to pay attention:
1. When purchasing new parts, pay attention to the quality of parts and identify fake and inferior products; carefully check whether the parts have rust spots, cracks, deformation and other defects, and whether the surface size meets the requirements.
2. The anti-rust coating on the surface of the new parts should be cleaned before assembly, especially the precision parts should be paid more attention to avoid potential accidents.
3. Deformed products are not universal, and some diesel engine factories produce the same type of deformed products, and their parts are not universal.
4. Replace some mating parts in pairs. For example, when replacing gears, you cannot replace only the one with the more severely worn one; when replacing the double-row sleeve roller chain in the transmission box, you must also replace the main and driven sprockets in pairs; when replacing the cylinder liner, you should replace the piston at the same time, Piston ring.
5. The standard parts and enlarged parts of the same model are not common. Manufacturers will produce enlarged spare parts for users to choose and match when repairing. Therefore, when purchasing spare parts, they must determine whether the purchased parts are standard parts or enlarged parts. Such as standard parts, the journal can only be equipped with standard crankshaft bushes, otherwise, the amount of processing when scraping the bearing bushes is very large, which wastes time, cannot guarantee the repair quality, and will greatly reduce the service life.
6. When replacing new parts, the new parts should be exactly the same as the old ones. When replacing new fuel injectors, some operators do not pay attention to the original fuel injector specifications and models, and often purchase needle valve couplings by mistake, which may cause difficulty in starting, or jam the fuel injector.
7. You must pay attention to the direction when installing. Some parts are directional, if you do not pay attention to, it will cause difficulty in starting after installation, and even damage the parts.
Autumn farm machinery to do a good jobprotection
--------------------------------------------------------------------------------
First of all, the weeds, soil and other items piled up outside the harvester should be removed in time, and the wheat straw, wheat bran, wheat grains and soil existing inside the machine should be removed. All kinds of casing, thin iron skin parts and other parts that are easy to rust should be repainted or fully painted and maintained to make the appearance free of rust spots..
For the parts that must be lubricated by the corn harvester, lubricating oil should be added in time to reduce friction, reduce the power consumption of the harvester, improve reliability, and extend the service life of the harvester. Add enough lubricating grease to each lubricating point; each exposed chain, sprocket, header blade row, plow blade, etc. should be removed and soaked in the oil pan, or coated with oil for maintenance, or coated with water and asphalt; unload the chain, Dipped with diesel oil, brush clean the oil and dirt, and then put it in the oil to soak, which can prolong the service life of the chain.
Secondly, the harvester must check the tightness of the triangle belt before operation. Too loose or too tight will affect the service life of the harvester. If the triangle belt is too loose, it will cause slippage and reduce work efficiency; if the triangle belt is too tight, it will increase bearing wear, increase power consumption, and may also cause the shaft to be pulled and bent. In addition, the harvester must check the tightness of the sprocket before operation. If it is too tight, it is easy to wear, and if it is too loose, the chain will jump and even cause tooth skipping and chain falling off. Once problems with agricultural machinery are found, the defective parts shall be replaced in time, and the broken parts of the support plate and support frame shall be repaired to ensure the integrity of the mechanical skeleton technology. If the rust of external equipment is serious, the whole vehicle shall be painted and stored. According to the maintenance requirements, lubricating grease shall be added to the operated agricultural machinery, loose bolts shall be tightened, and whether all parts are missing shall be checked. The missing parts shall be supplemented in time..
is best, after maintenance is completed, ensure that each locomotive up."four clean, three do not leak, one finishedgood."requirements, namely, clean oil, clean water, clean air, clean locomotive; No oil leakage, no water leakage, no air leakage; Only when the technical condition is intact can the warehouse be put into storage.
car tractor parts disassembly basic partylaw
--------------------------------------------------------------------------------
There are many ways to disassemble automobile and tractor parts, as long as the working surface and thread of parts and fasteners are not damaged, tools and people are not damaged, and the assembly can be carried out smoothly. The following disassembly methods are introduced.law:
1. common tools. For the disassembly of general parts, such as well-lubricated and lightly rusted fasteners, use common tools to remove them.;for specialspecial(specified torquemoment)fasteners can be removed with torque wrench and socket wrench. In case of chamfering of bolt and nut working surface, hammer can be used to knock it off and thentwist;the bolt gap of the screwdriver working surface slips, the saw bow can be used to re-examine the gap along the vertical position before disassembly.
2. percussion. The knocking method can be used for the disassembly of parts that are corroded due to long-term static fit, such as universal transmission cross shaft, steering rocker arm, various bearings and other parts. This method is widely used, its role is to destroy the corrosion between the parts of the bond, so that it produces vibration and release. When knocking, it is necessary to correctly select the parts to prevent the parts from being damaged, especially for the parts with high precision requirements, such as the disassembly of various bearings. In order to prevent the working surface from being damaged, soft cloth should be used to pad and tap with a hammer.
3. heating oil seepage method. For severely rusted parts that are difficult to disassemble. Such as steel leaf spring riding bolts, steering knuckle arm nuts, etc., due to long-term lack of maintenance, serious corrosion, this can be used to add oil seepage method, so that it can be lubricated after thermal expansion, and can be unscrewed. When heating, pay attention to whether there are flammable materials such as oil and rubber around the parts to prevent fire.
4. special screw hole disassembly method. For some parts that are difficult to disassemble, the parts arehave1-2a special removal hole. Such as transmission reverse gear shaft, drive half shaft, timing gear and other parts. The inner end of the hole has a thread matching with the screw. As long as the screw is screwed into the hole, the part can be automatically pushed out.
5. special puller and pressure regulator method. For the removal of spring parts, the press method can be used. Such as the removal of the valve spring. For difficult to disassemble the disc-shaped parts, available puller method. Such as the disassembly of various bearings, timing gears and other parts.
In short, the disassembly of agricultural vehicles and tractor parts is the basic skill of automobile and tractor maintenance and drivers. Whether the disassembly is smooth or not is directly related to the speed and quality of automobile maintenance. Therefore, the disassembly of automobile and tractor parts cannot be underestimated.
Greenhouse Rolling Machineprotection
--------------------------------------------------------------------------------
greenhouse rolling machine is an important equipment of agricultural facilities, with the adjustment of China's agricultural industrial structure, greenhouse planting is more and more valued by the government and farmers, farmers' income is growing. From the development of facility agriculture in recent years, the mainmachinery--greenhouse rolling machine has been recognized by the agricultural park and the majority of the planting industry, its role is more and more obvious, most of the agricultural park has the rolling machine as the main supporting equipment in the construction of the park.
1. the working form of rolling machine. At present, there are mainly two kinds of rolling machine: one is fixed, the rolling machine is fixed on the brick pile of the back wall of the greenhouse, the straw curtain is rolled up by mechanical power, and the straw curtain is rolled down by using the slope of the greenhouse and the weight of the straw curtain. The cost of this type of rolling shutter machine is relatively high, and the greenhouse must have a certain slope. If the slope of the shed surface is peaceful, the straw curtain cannot roll down. One is the walking type, the back wall has no brick stack, the installation is simple, the principle of manipulator is adopted, and the straw curtain is freely rolled up and down by the power of the rolling shutter machine, which is not limited by the slope size of the greenhouse. This model is currently used more.
2. the use and maintenance of rolling machine. Any kind of machinery in addition to its own quality and performance of its use and maintenance is to ensure the normal operation of machinery and the length of life of the main method. Rolling machine in the use and maintenance should pay attention to the following issues:
1, when the power supply to prevent the lack of a phase of power supply, if the lack of a phase of power supply will burn out the motor.
2, the transmission part of the host (such as reducer, transmission bearings, etc.), to add lubricating oil once a year.
3. During the installation process, the length (tightness) of the roller blind rope should be adjusted, and the rolled grass curtain should be in a straight line. In the process of use, the roller shutter rope should be adjusted frequently. If the rope length is not uniform and the grass curtain is not tight, the rolled grass curtain will appear curved, which will increase the torque force of the roller shutter machine and the reel in use, affecting the use effect or damaging the roller shutter machine and the reel.
4. Apply anti-rust paint to the parts once a year.
Common Mistakes in Agricultural Machinery Repairerror
--------------------------------------------------------------------------------
Install the cylinder head gasket and apply butter. Some operators like to apply a layer of butter on the cylinder block when installing the cylinder head gasket, thinking that this can improve the sealing performance. In fact, it is not, because the butter will dissolve and flow when exposed to high temperature, causing gaps between the cylinder head, cylinder block and the cylinder head gasket, and the gas is more likely to leak; the carbon deposits generated by the butter at high temperature will also cause the cylinder head gasket to age and increase the difficulty of assembly and disassembly. Repair brings trouble. Install the piston pin with open flame to heat the piston. Because the piston pin seat is thicker and the other parts are thinner, the thermal expansion coefficient of the open flame heating is very large, which is easy to deform the piston.
In addition, the temperature of open flame heating is difficult to control, and the piston is heated unevenly. The correct method of warming is to boil the piston in oil. Tighten the connecting rod screws without a torque wrench. When most operators tighten the connecting rod screws, they do not use a torque wrench, but use an ordinary wrench to tighten them hard.
Baler Operationcollar
--------------------------------------------------------------------------------
If the baler is not operated properly during use, it will not only delay working hours, but may be dangerous in serious cases. Therefore, it must be used in strict accordance with the operation essentials.
1.the connection of the main machine to the baler. The limit arm should be properly connected, too loose to play the role of limit, beating around the bush, the limit arm is easy to wear the rear tire of the main engine, the swing range is too large, and it is also easy to cause damage to its own parts, too tight, the turning angle increases, and the ground It is easy not to destroy the grass rake when turning.
2.twine does not enter. First, check whether the rope is entangled due to quality problems, for example, the knot head is too large and the hair head is too large. Second, check the density of the wheat knots at the rope entrance (left). If the density is not high enough, the friction between the rope and the wheat knots is not large enough. At this time, the left side of the baler can eat more grass to increase the friction at the rope entrance and promote rope feeding.
3.the adjustment of straw bales easy to scatter. When the wheat section has high humidity, it is easy to pick up and bundle, and the low density hole can be adjusted. When the wheat section is dry and fragile, it is not easy to pick up and feed, the high density hole should be adjusted. The straw can also be tied by adjusting the number of twine loops. Wheat straw dry, increase the number of loops, wheat straw wet, reduce the number of loops.
4.twine loop adjustment. Transfer to the big wheel, more twine loops,10rope; transferred to the small wheel, fewer laps,7road rope.
5.the length of the rope, so that the rope head just touches the blade.
6.protection screw is broken. When the baler is full of wheat festival, the alarm does not alarm, and the wheat festival will be piled up at the entrance. If you continue to walk at this time, the protection screw will break.
7.the reason why the alarm port does not alarm.(1) The power supply is not connected properly,(2) the wire is disconnected,(3) The circlip handle is out of the object handle slot.
8.the rope should be broken continuously, probably because the blade is dull, the blade should be replaced.
9.In the process of picking up grass, the driving speed of the power machinery can be slightly faster, when the small four-wheel drive2-the file.
10.the provision of wearing parts. Protective screws and blades should be equipped with grass to avoid delay in working hours.
Tractorlaw
--------------------------------------------------------------------------------
(1)The gear oil pump has insufficient oil supply, internal leakage of the gear oil pump or blockage of the filter screen in the steering oil tank, slow turning light, fast turning heavy. At this time, check whether the gear oil pump is normal and clean the filter screen.
(2)there is air in the steering system, turn the steering wheel, and the cylinder does not move when it moves. The air in the system should be removed, and the suction pipe should be checked for air intake, and the air should be discharged in time.
(3)The amount of oil in the steering oil tank is insufficient to reach the specified oil level. Should be refueled to the provisions of the oil level can be.
(4)the spring force of the safety valve becomes weak, or the steel ball is not sealed, the light load turns to light, and the increased load turns to sink. Safety valve shall be cleaned and spring pressure adjusted.
(5)the viscosity of the oil is too large, the specified hydraulic oil should be used.
(B)The steel ball check valve in the valve body fails, the fast and slow steering wheels are heavy, and the steering is weak. Should be cleaned, maintenance or replacement parts, troubleshooting.
(7)steering gear, including internalleakage(oilcylinder), external leakage. Oil leakage points shall be checked and removed.
The same abnormal occurrence before the engine failurelike
--------------------------------------------------------------------------------
The 22 operation station in the second management area of Heilongjiang Agricultural Reclamation 859 Farm is a farmground8more than 10,000 mu, there are hundreds of various kinds of dragging and planting machines, and many agricultural machinery handers, in years of production practice, can judge possible failures from the sound of tractor engines, appearance, timely and accurately from listening, smelling, looking, and touching. In the words of agricultural machinery handers, any failure is a precursor. Timely repair, thus saving manpower, financial resources, improve the efficiency of the tractor. Specifically summed up, there are the following six top table like:
1, abnormal appearance: oil leakage, air leakage, leakage and other phenomena everywhere, or black smoke and blue smoke from the exhaust pipe.
2, abnormal temperature: such as tractor engine overheating, bearing overheating or clutch overheating.
3. Abnormal smell: The exhaust pipe discharges the burnt smell of the friction plate issued by incomplete combustion.
4. Abnormal sound: when the tractor is working, there are shooting sounds, knocking sounds and some abnormal noises.
5, abnormal consumption: such as excessive consumption of oil, diesel and cooling water.
6, the role of abnormal: technicaloften, such as the tractor is difficult to start, the clutch slips, the traction edge is too small, there is no power, etc.
in response to the above-mentioned six anomalies, timely measures can be taken to prevent problems in the end.
Agricultural machinery parts rust removal partylaw
--------------------------------------------------------------------------------
accessories are an important part of the whole agricultural machinery, if part of the failure, the whole agricultural machinery can not operate normally. Therefore, for the parts must do a good job of inspection and maintenance. Due to long-term use, sun and rain, some parts will rust, do not take these rust, long-term may affect the operation of the whole agricultural machinery.
The following are three kinds of agricultural machinery parts rust method:
1, ammonium sulfate derusting method
use a large pottery tank to dress1:25ratio of prepared ammonium sulfate aqueous solution. Then the rusty farm tool parts into the cylinder, soak a day and night, the rust will float on its own. Take out the spare parts, wipe them off with a cloth and dry them, and coat them with lime milk or petroleum jelly.
2, baking soda rust removal method
a large vat of pottery, dressed up1:500proportion. After fully stirring, put rusty farm tool spare parts into the tank. After a certain period of time, the baking soda aqueous solution will begin to ferment and bubble. When a layer of rust crumbs floats on the liquid surface, take out the spare parts and wipe them clean with cloth, thus the true color of metal can be seen.
3, vinegar rust removal method
the rusty farm tool parts are soaked in vinegar, the rust layer is easy to fall off. After taking it out, use a fine brush to remove the rust on the accessories, then put it into vinegar to soak for a while, take it out, wipe it and dry it, and coat it with anti-rust oil.
Diesel Engine Maintenance Vlarge"banbogey"
--------------------------------------------------------------------------------
Avoid replacing the cylinder head gasket and not removing the residual cylinder head gasket
At present, some cylinder gaskets are graphite products. Such cylinder gaskets have strong adhesion and good sealing performance, which can only makeused1times. When the graphite cylinder gasket is removed, the residual old cylinder gasket adhered to the plane of the body and cylinder head must be removed. Due to the unevenness of the debris adhered to the contact surface of the body and the cylinder head, after the cylinder head is installed, the cylinder head gasket is not pressed, and it cannot withstand the impact of high temperature and high pressure gas when the diesel engine is working, and it is easy to damage the cylinder head gasket again.
two avoid installing the piston pin does not heat the piston
The aluminum piston expands greatly when heated, and the piston pin should be installed in the piston pin hole at room temperature. When installing, the piston should be heated in oil or water in advance.90℃or so, then take out the piston, and push the piston pin into the piston pin hole smoothly by hand while it is hot (pay attention to the assembly direction).
three avoid replacing the valve without grinding
In order to ensure the sealing of the valve, when replacing the valve and valve seat, first use a valve reamer with an appropriate angle to cut, and then apply the grinding paste between the valve and the valve seat, and use a valve grinder or manual grinding until Grindingout11~1.5mma wide, neat and continuous band of dark gray. The method of checking the valve tightness: clean the valve assembly and reinstall it on the cylinder head in its original position, and pour gasoline from the intake and exhaust ducts respectively,warp1~2minutes, observe that there is no leakage at the joint between the valve and the valve seat, which indicates that the seal is good.
Four avoid the back of the bearing pad iron skin or paper
The wear of the crankshaft journal and bearing bush exceeds a certain range, which increases the gap. During work, due to the leakage of oil, the oil pressure decreases, resulting in poor lubrication, aggravating wear, and abnormal knocking sounds. Repair method: The crankshaft should be removed and sent to the repair shop for grinding and repair with a crankshaft grinder, and then matched with a thickened bearing bush adapted to the size to restore its original performance. If you pad iron skin or paper on the back of the bearing bush, it will not reduce the gap between the shaft and the bush, but also deform the bearing bush when the crankshaft is under pressure, destroying the original gap, especially the pad paper, which can greatly reduce the heat transfer performance.
Five avoid replacing the oil indicator with a wooden prong
After the diesel engine is started, the oil indicator rises, which not only indicates that the diesel engine is well lubricated, but also exposes the oil nozzle hole, so that the oil is ejected from the hole to lubricate the back mechanism and make the diesel engine work normally. However, some operators find that the oil indicator is damaged, pull it out and throw it away, and smash it into the wooden prong. The wooden prong will block the oil nozzle, and the rocker arm mechanism will not be lubricated with oil, which will accelerate the wear of the parts.
walking tractortreatment
--------------------------------------------------------------------------------
many walking tractors have a common fault, that is, the clutch shaft is thrown outward oil. Some drivers have to install an iron sheet near the clutch to block the oil, and some hang a bottle under the clutch to contain the leaked gear oil. These are negative measures and do not prevent the gear oil from being thrown out. These gear oil is from the chain belt of the transmission box, leaking from the clutch shaft and the bearing cover with claw and the separation claw seat.
Main Causes of Oil Throwed by 1. Clutch Shaft
1. There are flaws in the design. At present, many walking tractors still use the old design in the early years. There is no oil seal on the claw bearing cover, and some separation claw seats have no spiral oil return groove in the inner hole, or the spiral oil return groove is turned in the wrong direction. In addition, the matching clearance between the separation claw seat and the claw bearing cover and the clutch shaft is large, so oil throwing is inevitable.
2. The use of the environment is too harsh. Since the walking tractor does not have a cab, the clutch and other components are often eroded by rain. When engaged in paddy field rotary tillage operations, muddy water splashes everywhere, and when sowing and harvesting operations, dust is flying, which is easy to stain the separation claw, separation claw seat and clutch shaft and other parts. Due to the harsh environment, the wear of the parts is accelerated, the gap between the parts is too large, and the gear oil is easily thrown out.
3. Due to the wear of the bearings at both ends of the clutch, or the excessive tension of the transmission belt, the clutch shaft is bent, causing the clutch shaft to tilt, and the shaft and the separation claw seat are engaged, so the clutch shaft drives the separation claw seat to rotate together, which eventually leads to oil rejection.
2. clutch
1. Improve product design. The manufacturer should change the old design and install an oil seal or adopt a better structure at the bearing cover with claw.
2. Turning spiral groove. A spiral groove with sufficient depth is made in the inner hole of the separation claw seat to guide the escaping gear oil back to the transmission box.
3. Grease filling.Before installing the rolling bearing, fill the base grease into the claw bearing cup and apply grease to the inner wall of the separating claw seat. After using for a period of time, you can remove the clutch assembly and the separating claw, and add pressure injection grease to the separating claw seat until the separating claw seat squeezes out the grease.
rotary tillerItem
--------------------------------------------------------------------------------
The working characteristic of the rotary tiller is that the working parts rotate at high speed, and almost all safety problems are related to this. To this end, in the use of rotary tiller to pay attention to the following points:
1. Before use, check all parts, especially check whether the rotary blade is installed backwards and whether the fixing bolts and universal joint lock pins are firm. If problems are found, they should be handled in time and can be used only after confirmation.
2and tractor, turn the clutch handle of the rotary tiller to the separated position.
3. The power shall be engaged in the lifting state. After the rotary tiller reaches the predetermined speed, the unit can start, and the rotary tiller shall be slowly lowered to make the rotary tiller go into the soil. It is strictly forbidden to start directly under the condition that the rotary tiller knife is buried to prevent the rotary tiller knife and related parts from being damaged. It is strictly forbidden to descend the rotary tiller rapidly, and it is strictly forbidden to reverse and turn after the rotary tiller knife is buried.
4. When the power is not cut off when the ground turns, the rotary tiller shall not be raised too high, and the transmission angle at both ends of the universal joint shall not exceedover30degrees, and the engine speed should be appropriately reduced. When transferring plots or walking long distances, the power of the rotary tiller should be cut off and locked after rising to the highest position.
5. When the rotary tiller is running, people are strictly prohibited from approaching the rotating parts, and no one is allowed behind the rotary tiller, in case the blade is thrown out and hurt people.
6. When checking the rotary tiller, the power must be cut off first. When replacing rotating parts such as blades, the tractor must be turned off.
7, speed of progress during farming, dry field2~3km/h is appropriate in plowed or raked fields5~7km/h is appropriate, farming in paddy fields can be appropriate and faster. Remember, the speed can not be too high, in order to prevent the tractor overload and damage the power output shaft.
8. When the rotary tiller is working, the wheels of the tractor shall walk on the uncultivated land to avoid compaction of the cultivated land. Therefore, the wheel track of the tractor shall be adjusted to make the wheels within the working width of the rotary tiller. Pay attention to the walking method during operation to prevent the other wheel of the tractor from compacting the cultivated land.
9. During operation, if the knife shaft is too wrapped with grass, stop and clean it in time to avoid increasing the load of machines and tools.
10and rotary tillage, the tractor and suspension parts are not allowed to take people to prevent accidental injury by the rotary tiller.
11. When using the walking tractor rotary tiller unit, the rotary tillage gear can only be engaged when the auxiliary gear lever is in the slow position. If you need to reverse during work, you must put the auxiliary gear lever in neutral to engage reverse gear. Try not to use the steering clutch in the rotary tillage, and apply the push-pull armrest to correct the direction. When turning on the ground, you should first reduce the throttle, hold up the armrest, and then pinch the steering clutch. Do not turn the corner to prevent damage to the parts.
